AMOCAM V70C-520-3

AMOCAM V70C-520-3 3-Unit Apartment Video Intercom System User Manual

Model: V70C-520-3 | Brand: AMOCAM

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your AMOCAM V70C-520-3 3-Unit Apartment Video Intercom System. This system is designed to enhance security and communication for multi-household buildings, featuring a 7-inch indoor monitor, an outdoor IR camera, and two-way intercom functionality. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Package Contents

Verify that all items listed below are included in your package. If any items are missing or damaged, please contact customer support.

3. Safety Information

Observe the following safety precautions to prevent damage to the product and ensure user safety:

4. Setup and Installation

This section outlines the steps for installing your video intercom system. The system uses a wired connection for stable performance.

4.1 Outdoor Unit Installation

  1. Mounting Location: Choose a location near your entrance, typically beside the door, where the camera can capture a clear view of visitors. The recommended height for the camera lens is between 145-160 cm (approximately 57-63 inches) from the ground, with the call button around 126 cm (approximately 50 inches).
  2. Secure the Bracket: Pass the set iron through the holes on both sides of the outdoor station. Fix the bottom cover to the wall using the provided screws.
  3. Wiring: Connect the necessary wires (video, audio, power) from the outdoor unit to the main distribution point according to the wiring diagram.
Installation diagram for the AMOCAM video intercom system, showing standard height for outdoor station installation (145-160cm camera lens height, 126cm call button height), and a detailed wiring schematic connecting the outdoor unit to multiple indoor monitors and an electric lock.

Figure 4.1: Outdoor Unit Installation Diagram and Wiring Schematic

4.2 Indoor Monitor Installation

  1. Mounting Location: Select a convenient indoor location for each monitor, such as a living room or hallway.
  2. Secure the Bracket: Install the wall bracket for each indoor monitor using screws.
  3. Wiring: Connect the indoor monitor to the main distribution point using the provided connection cables. Ensure all connections are secure. Refer to the wiring diagram for correct terminal connections.
  4. Power Connection: Plug in the power supply for each indoor monitor.
  5. Hang the Monitor: Once wiring is complete, hang the indoor monitor onto its bracket.
Rear view of the AMOCAM indoor monitor, showing wiring terminals for GND, DC15V, Video, Audio, and Power connections.

Figure 4.2: Indoor Monitor Wiring Terminals

4.3 System Wiring Overview

The system utilizes a wired connection for reliable communication. The outdoor unit connects to a central point, which then distributes signals to each indoor monitor. An electric lock can also be integrated into the system for remote door unlocking.

Wiring Diagram Explanation:

Ensure all wires are connected to their corresponding terminals on both the outdoor unit and indoor monitors. Incorrect wiring can lead to system malfunction or damage.

This video demonstrates the AMOCAM V70C-520-3 3-Unit Apartment Video Intercom System, showcasing its components, wiring connections, and operational features such as calling, monitoring, and two-way communication between the outdoor unit and indoor monitors.

5. Operating Instructions

This section details how to use the various functions of your AMOCAM video intercom system.

5.1 Indoor Monitor Functions

Side view of the AMOCAM indoor monitor showing control knobs for intercom volume, music & ring volume, monitor, unlock, brightness, and screen color.

Figure 5.1: Indoor Monitor Controls

5.2 Outdoor Unit Functions

AMOCAM outdoor camera unit, front view, featuring call buttons and camera lens.

Figure 5.2: Outdoor Unit Front View

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your AMOCAM video intercom system.

7. Troubleshooting

If you encounter issues with your system, refer to the following common problems and solutions:

ProblemPossible CauseSolution
No video on indoor monitorLoose video cable connection; power issue; camera malfunction.Check all video cable connections. Ensure the outdoor unit and indoor monitor are powered. If the issue persists, contact support.
No audio during intercomLoose audio cable connection; volume too low; microphone/speaker malfunction.Verify audio cable connections. Adjust intercom volume on the indoor monitor. Check for obstructions on the microphone/speaker.
Doorbell not ringingLoose call button wiring; chime volume too low; monitor not powered.Check call button wiring. Increase the 'Music & Ring volume' on the indoor monitor. Ensure the monitor has power.
Door unlock function not workingIncorrect electric lock wiring; incompatible lock; power issue to lock.Verify electric lock wiring according to the diagram. Ensure the lock receives power. Confirm lock compatibility.
Poor video quality at nightObstruction to IR sensors; dirty camera lens.Clean the camera lens. Ensure no objects are blocking the IR sensors on the outdoor unit.

If these steps do not resolve the issue, please contact AMOCAM customer support for further assistance.

8. Specifications

Below are the technical specifications for the AMOCAM V70C-520-3 Video Intercom System:

9. Warranty and Support

AMOCAM products are designed for reliability and performance. For specific warranty details, please refer to the warranty card included with your purchase or visit the official AMOCAM website. For technical support, troubleshooting assistance, or inquiries regarding parts and service, please contact AMOCAM customer service through the contact information provided on their website or your purchase documentation.

Related Documents - V70C-520-3

Preview WOLILIWO 2-4 Unit Apartment Video Intercom System User Manual
Comprehensive user manual for the WOLILIWO 2-4 unit Apartment Video Intercom System, covering product structure, functions, wiring schematics, installation instructions, and troubleshooting.
Preview Ring Software Version History and Release Notes
Comprehensive release notes and version history for Ring software updates, detailing firmware versions, release dates, device compatibility, and file sizes for Ring Alarm, Video Doorbells, Surveillance Cameras, Access Control devices, and Accessories.
Preview Ring Playbook: Ontdek Slimme Deurbellen, Camera's en Beveiligingssystemen
Verken het Ring Playbook voor een uitgebreid overzicht van Ring's slimme deurbellen, beveiligingscamera's, Ring Alarm en accessoires. Leer hoe Ring je huis veiliger maakt.
Preview Troubleshooting Guide for Ring Video Doorbell Solar Charger
This guide provides troubleshooting steps for the QIBOX Solar Charger, addressing common issues such as the solar panel not working, slow charging, and compatibility with Ring Video Doorbell models. It includes installation instructions and tips for optimal performance.
Preview Satisure Anti-Theft Doorbell Mount: Installation Guide
Comprehensive guide for installing the Satisure Anti-Theft Doorbell Mount using both no-drill and drilling methods. Compatible with major video doorbell brands like Ring and Blink.
Preview SCS Sentinel VisioKit 4.3 Wired Video Intercom System - Installation and User Manual
Comprehensive guide for the SCS Sentinel VisioKit 4.3 wired video intercom system. Covers installation, wiring, usage, settings, technical specifications, safety warnings, and warranty information for this 2-wire video door entry system.