1. Introduction
Thank you for choosing the VECHLINE Visio Evo Dual Reversing Camera, Model 668. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new reversing camera system. Please read this manual thoroughly before attempting to install or operate the device.
2. Safety Information
- Always disconnect the vehicle's battery before performing any electrical work.
- Ensure all wiring is properly insulated and secured to prevent short circuits or damage.
- Mount the camera securely to avoid detachment during vehicle movement.
- Do not obstruct the driver's view or interfere with vehicle safety features.
- Consult a professional if you are unsure about any installation steps.
- This device is designed as an aid and should not replace careful driving and observation.
3. Product Overview
The VECHLINE Visio Evo Dual Reversing Camera system provides enhanced visibility for safer maneuvering of your vehicle. It features two cameras for comprehensive rear coverage and connects to a compatible 7-inch LED display (sold separately) for clear video output.
Figure 1: The VECHLINE Visio Evo Dual Reversing Camera. This image shows the compact black camera unit with two distinct lenses, indicating its dual functionality. Two black connector cables with silver ends are visible to the right of the camera, ready for connection to the vehicle's electrical system and display unit.
4. Setup and Installation
4.1 Mounting the Camera
- Select Location: Choose a suitable mounting location at the rear of your vehicle that provides an unobstructed view and protects the camera from damage. The camera is designed for surface mounting.
- Secure Mounting: Use appropriate screws and hardware to securely attach the camera bracket to the chosen surface. Ensure the camera is stable and does not vibrate.
- Adjust Angle: Once mounted, adjust the camera's angle to achieve the desired field of view. The camera offers a 165-degree actual viewing angle.
4.2 Wiring Connections
The camera uses RCA connectors for video output. Ensure your display unit is compatible with RCA inputs.
- Power Connection: Connect the camera's power cable to a suitable 12V DC power source in your vehicle. It is recommended to connect it to the reverse light circuit so the camera activates automatically when reversing, or to an ignition-switched power source for continuous operation.
- Video Connection: Connect the RCA video output cables from the camera to the corresponding video input ports on your 7-inch LED display unit. Ensure correct channel assignment if your display supports multiple inputs.
- Cable Routing: Route all cables carefully, avoiding sharp edges, moving parts, and heat sources. Use cable ties to secure them.
5. Operating Instructions
5.1 Powering On/Off
The camera system will power on automatically when the connected power source is active (e.g., when the vehicle is in reverse or ignition is on). It will power off when the power source is disconnected.
5.2 Switching Camera Views
If your display unit supports multiple camera inputs, you can switch between the two camera views using the display's controls. Refer to your display unit's manual for specific instructions on input selection.
5.3 Adjusting Display Settings
Adjust brightness, contrast, and color settings on your connected 7-inch LED display for optimal viewing conditions. The camera provides a 1080p video recording resolution for clear images.
6. Maintenance
6.1 Cleaning the Camera Lens
Periodically clean the camera lenses with a soft, damp cloth to remove dirt, dust, or water spots that may obstruct the view. Do not use abrasive cleaners or solvents.
6.2 Inspecting Connections
Regularly check all wiring connections for signs of wear, corrosion, or looseness. Ensure all cables are securely fastened.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No image on display | No power to camera or display; Loose video connection; Incorrect input selected on display. | Check power connections; Ensure video cables are securely connected; Select correct video input on display. |
| Distorted or flickering image | Poor video connection; Electrical interference; Damaged cable. | Check video cable integrity and connections; Ensure proper grounding; Reroute cables away from interference sources. |
| Camera not turning on | No power supply; Blown fuse; Faulty wiring. | Verify power connection; Check vehicle fuses; Inspect wiring for damage. |
| Image is blurry or unclear | Dirty lens; Condensation on lens; Incorrect display settings. | Clean camera lens; Allow time for condensation to clear; Adjust display focus/sharpness settings. |
8. Specifications
- Brand: VECHLINE
- Model: 668
- Item Model Number: 668
- Display Technology: LED (for compatible display)
- Screen Size (compatible display): 7 Inch
- Video Recording Resolution: 1080p
- Lens Type: Wide-angle
- Actual Viewing Angle: 165 Degrees
- Field of View: 165 Degrees
- Optical Sensor Technology: CMOS
- Installation Type: Surface Mount
- Connector Type: RCA
- Item Weight: 2 kg
- First Available Date: November 24, 2022
- Guaranteed Software Updates Until: Unknown
9. Warranty and Support
For warranty information and technical support, please refer to the documentation provided with your purchase or contact your VECHLINE retailer. Keep your proof of purchase for warranty claims.