1. Introduction
Thank you for choosing the LARSON 80 Split Fullview Storm Door with Low-E Glass. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new storm door. Please read all instructions carefully before beginning installation or use.
Image 1.1: The LARSON 80 Split Fullview Storm Door, designed to enhance your home's exterior.
2. Safety Information
Always prioritize safety during installation and use. Failure to follow these instructions may result in injury or damage to the product.
- Wear appropriate safety gear: Always wear safety glasses, gloves, and other protective equipment during installation.
- Handle glass with care: The door features tempered safety glass. Handle glass panels carefully to prevent breakage and injury.
- Secure the door during installation: Ensure the door is properly supported and secured to prevent it from falling or swinging unexpectedly.
- Use correct tools: Use only the tools recommended in the installation guide.
- Keep children and pets away: During installation, keep children and pets clear of the work area.
- Proper lifting techniques: The door is heavy (approximately 59 pounds). Use proper lifting techniques or seek assistance to avoid back injury.
- Electrical safety: If working near electrical outlets or wiring, ensure power is off to prevent electrical shock.
3. Package Contents
Before beginning installation, verify that all components are present. If any parts are missing or damaged, contact customer support immediately.
The LARSON 80 Split Fullview Storm Door package includes:
- Storm Door Frame with Integrated Full-View Low-E Glass
- Retractable Screen System
- Installation Hardware (hinges, screws, etc.)
- Two Door Closers
- Installation Instructions
Note: The door handle set is sold separately and is not included with this storm door. Please refer to the product description for compatible handle sets.
Image 3.1: Example of QuickFit™ Handlesets, which are sold separately.
4. Setup & Installation
This storm door is designed for simple installation into most standard door openings. However, proper measurement and preparation are crucial for a successful fit.
4.1. Measuring Your Door Opening
Accurate measurements are essential. Measure the width of your door opening horizontally at the top, middle, and bottom. Record the narrowest dimension. Then, measure the vertical opening height. This door requires a 1-inch deep mounting surface and 1-inch wide flat trim on the outside for proper installation.
Image 4.1: Guide for measuring your door opening to ensure proper storm door fit.
4.2. Pre-Installation Checks
- Ensure your door frame is clean, level, and free of obstructions.
- Confirm that the door opening meets the required dimensions for your storm door size.
- Gather all necessary tools, including a drill, screwdriver, measuring tape, level, and safety gear.
4.3. Installation Steps
Refer to the detailed installation guide included with your product for step-by-step instructions. Key steps generally include:
- Prepare the door frame and ensure it is plumb and square.
- Install the hinge rail to the door frame.
- Mount the storm door onto the hinge rail.
- Install the latch rail and adjust for proper sealing.
- Install the two door closers, ensuring they are positioned to allow the door to open to approximately 110 degrees without overextending.
- Install your separately purchased handle set according to its specific instructions.
- Perform final adjustments to ensure smooth operation and a tight seal.
5. Operating Instructions
The LARSON 80 Split Fullview Storm Door features a convenient retractable screen and full-view glass for versatile use.
5.1. Retractable Screen Away & EasyVent Technology
This door is equipped with a Retractable Screen Away system, allowing you to seamlessly switch between a full glass panel and a screen for ventilation. The EasyVent Technology provides an adjustable screen for customized airflow.
- To lower the glass and reveal the screen: Locate the release mechanism (typically a handle or button) on the top glass panel. Engage the mechanism and gently slide the glass panel downwards. The screen will automatically deploy from the bottom.
- To raise the glass and conceal the screen: Grasp the top glass panel and gently slide it upwards until it locks into place. The screen will retract into the door frame.
Image 5.1: Operating the door closer with a foot for convenience.
5.2. Door Closers
The two included door closers control the speed and force of the door's closing action. Adjust the tension on the closers to achieve your desired closing speed. Ensure the door closers allow the door to open fully (approximately 110 degrees) without straining the hinges.
6. Maintenance
Regular maintenance will ensure the longevity and optimal performance of your LARSON storm door.
- Cleaning the Frame: The durable aluminum frame with a rust-resistant finish can be cleaned with mild soap and water. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
- Cleaning the Glass: Use a standard glass cleaner and a soft cloth to clean the Low-E glass. For best results, clean on a cloudy day to prevent streaks.
- Cleaning the Screen: The retractable screen can be gently wiped with a damp cloth to remove dust and debris.
- Lubrication: Periodically lubricate moving parts such as hinges and the retractable screen mechanism with a silicone-based lubricant to ensure smooth operation.
- Weather-Resistant Seal: Inspect the weather-resistant seals around the door frame annually for any signs of wear or damage. Replace if necessary to maintain energy efficiency and prevent drafts.
7. Troubleshooting
This section addresses common issues you might encounter with your storm door.
| Problem | Possible Cause | Solution |
|---|---|---|
| Door does not close or latch properly. |
|
|
| Door closers prevent the door from opening fully. | Door closers installed too far from the door or tension is too high. | Reposition the door closers closer to the door frame or reduce the tension. The door should open to approximately 110 degrees. |
| Retractable screen or glass sticks. |
|
|
| Drafts or moisture entering around the door. | Damaged or improperly sealed weatherstripping. | Inspect and replace any worn or damaged weatherstripping. Ensure the door is properly aligned and closes tightly against the seals. |
8. Specifications
Key specifications for the LARSON 80 Split Fullview Storm Door (Model 14604032E):
Image 8.1: The storm door features energy-efficient Low-E Glass.
| Feature | Detail |
|---|---|
| Brand | Larson |
| Model Number | 14604032E |
| Type | 80 Split Fullview Storm Door |
| Glass Type | Low-E Glass (Tempered Safety Glass) |
| Frame Material | Durable Aluminum |
| Finish | Rust-Resistant |
| Screen | Retractable Screen Away with EasyVent Technology |
| Door Closers | 2 included |
| Approximate Item Weight | 59 pounds |
| UPC | 092304144795 |
9. Warranty & Support
For specific warranty details, please refer to the warranty card included with your product or visit the official Larson website. Larson provides support for product inquiries, missing parts, and technical assistance.
Customer Support: For assistance, please contact Larson customer service through their official website or the contact information provided in your product packaging.
