1. Introduction and Overview
This manual provides detailed instructions for the installation, operation, and maintenance of your Golight 2020-D Dash Mount Remote. This remote control unit is designed to provide convenient and precise control over compatible Golight/Radioray searchlights from your vehicle's dashboard.
Figure 1: The Golight 2020-D Dash Mount Remote Control Unit. This image displays the compact black control panel with two rotary switches and a central toggle switch, along with wiring extending from the rear.
Please read this manual thoroughly before attempting installation or operation to ensure proper function and safety.
2. Setup and Installation
Proper installation is crucial for the optimal performance of your Golight 2020-D remote. It is recommended that installation be performed by a qualified technician.
2.1 Safety Precautions
- Disconnect all power to the vehicle and searchlight system before beginning installation.
- Ensure all wiring connections are secure and properly insulated to prevent short circuits.
- Mount the remote in a location that does not obstruct the driver's view or interfere with vehicle controls.
2.2 Mounting the Remote
- Select a flat, secure surface on your vehicle's dashboard for mounting.
- Use the provided template (if applicable, or measure the unit) to mark the cutout area for the remote.
- Carefully cut the opening in the dashboard.
- Drill pilot holes for the mounting screws.
- Insert the remote into the cutout and secure it with the provided screws.
2.3 Wiring Connections
Refer to the wiring diagram provided with your Golight searchlight for specific connections. Generally, the remote will require connections for:
- Power (12V DC): Connect to a fused 12V power source.
- Ground: Connect to a reliable vehicle ground point.
- Control Wires: Connect to the corresponding control wires of your Golight/Radioray searchlight for pan, tilt, and power functions.
Ensure all connections are tight and protected from moisture and abrasion.
3. Operating Instructions
The Golight 2020-D remote provides intuitive control over your searchlight's functions.
3.1 Control Layout
- Left Rotary Switch: Typically controls the Pan (left/right) movement of the searchlight. Rotate the switch to the desired direction.
- Right Rotary Switch: Typically controls the Tilt (up/down) movement of the searchlight. Rotate the switch to the desired direction.
- Center Toggle Switch: Usually functions as the Power ON/OFF switch for the searchlight. Flip the switch to turn the searchlight on or off.
3.2 Basic Operation
- Ensure the vehicle's ignition is on (if wired to an accessory circuit).
- Flip the center toggle switch to the "ON" position to power on the searchlight.
- Rotate the left switch to pan the searchlight left or right.
- Rotate the right switch to tilt the searchlight up or down.
- When finished, flip the center toggle switch to the "OFF" position to power off the searchlight.
Familiarize yourself with the controls in a safe environment before using the searchlight in critical situations.
4. Maintenance
The Golight 2020-D Dash Mount Remote is designed for durability and requires minimal maintenance.
- Cleaning: Periodically wipe the surface of the remote with a soft, damp cloth. Avoid using harsh chemicals or abrasive cleaners.
- Inspection: Regularly check the wiring connections for any signs of wear, corrosion, or looseness. Ensure the mounting screws remain tight.
- Environmental Protection: While designed for vehicle use, avoid exposing the remote to extreme temperatures or direct water spray for extended periods.
5. Troubleshooting
If you encounter issues with your Golight 2020-D remote, refer to the following common troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote is unresponsive. | No power to the remote or searchlight. Loose wiring connection. Blown fuse. | Check vehicle's power supply. Inspect all wiring connections. Check and replace any blown fuses in the circuit. |
| Searchlight does not pan/tilt. | Faulty control wire connection. Searchlight motor issue. | Verify control wire connections between the remote and searchlight. Consult the searchlight's manual for motor troubleshooting. |
| Intermittent operation. | Loose or corroded connections. | Inspect all wiring for corrosion or loose terminals and secure them. |
If problems persist after attempting these solutions, contact Golight customer support or a qualified service technician.
6. Specifications
| Feature | Detail |
|---|---|
| Model Number | 2020-D |
| Manufacturer Part Number | 2020-D |
| Brand | Golight |
| Item Weight | 8.7 ounces |
| Product Dimensions | 5 x 5 x 4 inches |
| Compatibility | Designed for Golight/Radioray searchlights (2020 series) |
7. Warranty and Support
Specific warranty details for the Golight 2020-D Dash Mount Remote are not provided within this document. For information regarding warranty coverage, technical support, or replacement parts, please refer to the official Golight website or contact their customer service directly.
Golight Official Website: www.golight.com
