Introduction
The CURRENT USA Satellite Plus Pro Freshwater LED Light is designed to provide optimal lighting for freshwater aquariums, promoting strong plant growth and vibrant fish colors. This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your Satellite Plus Pro LED fixture.
This advanced lighting system features full spectrum RGB+W LEDs, wireless remote control, and programmable 24-hour timer functions, allowing for dynamic lighting effects and customized light cycles.
Important Safety Information
Please read and understand all safety instructions before operating this product. Failure to follow these instructions may result in injury or product damage.
- Ensure the power supply is disconnected before performing any maintenance or installation.
- This product is designed for indoor use only.
- Do not immerse the fixture or power supply in water. The fixture is IP65 rated for water resistance, but the power supply is not.
- Always connect the AC plug to a GFCI (Ground Fault Circuit Interrupter) socket.
- Keep out of reach of children.
- Do not operate if any part of the fixture or wiring is damaged.
Package Contents
Verify that all components are present before proceeding with installation:
- Satellite Plus Pro LED Fixture
- Wireless Remote Control
- DC Power Supply (Transformer)
- Adjustable Docking Mounts
- User Manual (this document)
Image: The Satellite Plus Pro LED light fixture, its wireless remote control, and the inline controller unit.
Setup Instructions
- Attach Docking Mounts: Slide the adjustable docking mounts onto each end of the LED fixture. Adjust the mounts to fit the length of your aquarium.
- Position Fixture: Place the assembled LED fixture securely on top of your aquarium. Ensure it is stable and centered.
- Connect Controller: Connect the 5-pin receptacle on the LED fixture to the 5-pin plug on the controller unit. Ensure a secure connection.
- Connect Power Supply: Connect the DC plug from the transformer (power supply) to the DC receptacle on the controller unit.
- Plug into GFCI: Plug the AC plug from the transformer into a GFCI (Ground Fault Circuit Interrupter) protected electrical socket.
- Power On: Press the POWER button on the top right corner of the wireless remote control to turn on the fixture.
Image: A hand demonstrating how to adjust the docking mounts on the LED light fixture to fit the aquarium.
Setup Video Guide
Video: A detailed installation guide for the Satellite Plus Pro LED light, demonstrating how to set up the fixture and connect its components.
Operating Instructions
The Satellite Plus Pro offers extensive control via its wireless remote. The controller unit features a digital display for settings.
Setting the Clock
- Press the SET CLOCK button on the remote. The time displayed on the controller will flash.
- Use the HOUR and MINUTE buttons to adjust to the correct current time.
- Press ENTER to program the current time.
Setting On/Off Times
- To set the time you'd like your light to turn on, press the ON TIME button. Use the HOUR and MINUTE buttons to adjust to the desired on time. Press ENTER to program the on time.
- To set the time you'd like your light to turn off, follow the previous steps using the OFF TIME button.
Adjusting Daylight and Moonlight Colors
- To set your Daylight Color, start by pressing one of the four preset colors (white, red, green, blue) or the Daylight button.
- Using the four color adjustment buttons (up/down arrows for each color channel), increase or decrease to the desired color. Each color can be adjusted from 0-100 and is displayed on the digital display.
- Once the desired color is achieved, press and hold the Daylight button until the lights on the fixture flash and the digital display shows "S3". This saves your custom daylight setting.
- To set your Moon Light color, follow the previous steps using the Moon Light button. Once the desired color is achieved, press and hold the Moon Light button until the lights on the fixture flash and the digital display shows "S4".
- Daylight and Moonlight colors can be adjusted at anytime using the previous steps.
Programming Custom Colors into Memory (M1/M2)
- Press any one of the preset colors (white, red, green, blue) or adjust colors using the four color adjustment buttons to achieve your desired custom color.
- Once the desired color is achieved, press and hold the M1 or M2 button until the lights on the fixture flash. The digital display will show "S1" or "S2" indicating the memory location.
- To recall a saved custom color, simply press the M1 or M2 button.
Dynamic Modes
The Satellite Plus Pro features several dynamic lighting effects:
- Cloud Cover
- Fading Lunar
- Storm
- Lightning
To select a Dynamic Mode, press one of the four buttons at the bottom of the remote corresponding to the desired effect. To exit the dynamic mode and resume to the programmed lighting cycle, press RESUME.
Video: A demonstration of setting the clock, on/off times, and adjusting colors on the Satellite Plus Pro LED light using the remote control.
Maintenance
Regular maintenance ensures optimal performance and longevity of your LED fixture.
- Cleaning: Periodically wipe the LED fixture with a soft, damp cloth to remove dust, water spots, and algae buildup. Do not use abrasive cleaners or solvents.
- Power Supply: Ensure the power supply and connections remain dry and free from corrosion.
- Ventilation: Ensure the fixture has adequate airflow around it to prevent overheating.
- Cable Inspection: Regularly inspect the power cable and connections for any signs of damage. Replace immediately if damaged.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the unit; loose connections; faulty power supply/fixture. | Check power outlet and GFCI. Ensure all connections are secure. Test with another outlet. Contact customer support if problem persists. |
| Remote control not responding. | Remote batteries are dead; remote sensor blocked; remote out of range. | Replace remote batteries (2 CR2 required). Ensure no obstructions between remote and controller. Operate remote within close range (e.g., 4 ft or less). |
| Lights are dim or flickering. | Incorrect brightness setting; power supply issue; LED degradation. | Adjust brightness using the remote. Check power connections. If LEDs are degrading (e.g., half LEDs gone after 2.5 years), consider replacement. |
| Timer settings are not working. | Incorrect clock setting; incorrect ON/OFF times programmed. | Re-set the clock and ON/OFF times carefully following the operating instructions. Ensure ENTER is pressed after each setting. |
Specifications
- Model: 4012
- Dimensions: 3.5"D x 34.8"W x 0.44"H (for 36"-48" model)
- Item Weight: 2.7 Pounds
- Material: Aluminum
- Light Source Type: LED (6500K White LEDs and RGBW LEDs)
- Wattage: 60 watts (Maximum)
- Voltage: 12VDC
- Connectivity Technology: IR (Infrared Remote Control)
- Water Resistance Level: IP65 Rated (fixture only)
- Power Source: Corded Electric
- Controller Type: Remote Control
- UPC: 842959040122
Warranty & Support
This product comes with a 1-year manufacturer warranty. For warranty claims or technical support, please contact CURRENT USA directly.
Contact Information: Refer to the manufacturer's website or the original product packaging for the most current support details.
Additional Resources:
