1. Introduction
The BlackFire BBM920 Clamplight Backpack Lantern is a versatile and compact lighting solution designed for various applications. It features a unique combination of a carabiner for easy attachment and a robust clamp for hands-free operation. Equipped with two separate groups of 100,000-hour LEDs (eight Kong LEDs for lantern mode and one Cree LED for flashlight mode), it delivers optimal performance and light output. Its articulating head allows for precise light direction, and the durable, rubberized coating ensures a secure grip and enhanced toughness.
An image of the BlackFire BBM920 Clamplight Backpack Lantern, showing its compact black body with green accents, the translucent lantern top, the articulating head, and the integrated carabiner and clamp mechanisms.
2. Safety Information
- Read all instructions thoroughly before operating the device.
- Keep the lantern out of reach of children.
- Do not mix old and new batteries, or different types of batteries.
- Ensure correct battery polarity (+/-) when installing.
- Remove batteries if the device will not be used for an extended period to prevent leakage.
- Dispose of used batteries according to local regulations.
- The device is IPX4 water resistant, meaning it is protected against splashing water from any direction. Do not submerge the lantern in water.
- Do not look directly into the LED light source to avoid eye strain.
3. Package Contents
- BlackFire BBM920 Clamplight Backpack Lantern (1)
- Note: Three (3) AAA batteries are required and not included.
4. Setup
4.1 Battery Installation
- Locate the battery compartment on the base of the lantern.
- Twist or unlatch the compartment cover to open it.
- Insert three (3) AAA batteries into the compartment, ensuring that the positive (+) and negative (-) ends align with the markings inside.
- Securely close the battery compartment cover.
5. Operating Instructions
5.1 Power On/Off and Mode Selection
The BlackFire BBM920 features four distinct modes of operation: High, Low, Strobe (Lantern), and Flashlight mode. An IC chip ensures consistent light output across modes.
- To Turn On: Press the power button (typically located on the side or front) once. The lantern will usually activate in High mode.
- To Cycle Modes: Press the power button repeatedly to cycle through the available modes: High > Low > Strobe (Lantern) > Flashlight.
- To Turn Off: Continue pressing the power button until the light turns off, or hold the button down for a few seconds in any mode.
5.2 Using the Carabiner
The integrated carabiner allows for convenient attachment and portability.
- Open the carabiner gate.
- Attach the lantern to backpack straps, belt loops, tent loops, or other suitable attachment points.
- Ensure the gate is securely closed after attachment.
5.3 Using the Clamp
The built-in clamp provides hands-free illumination by securing the lantern to various surfaces.
- Open the clamp jaws by pressing the release mechanism or spreading them apart.
- Attach the clamp to a table edge, branch, pole, or other stable surface.
- Ensure the clamp has a firm grip on the surface before releasing.
- Articulating Head: Adjust the lantern's head to direct the light precisely where it is needed.
6. Maintenance
- Cleaning: Wipe the exterior of the lantern with a soft, damp cloth. Do not use harsh chemicals, abrasive cleaners, or solvents, as these may damage the finish or internal components.
- Storage: Store the lantern in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Care: If the lantern will not be used for an extended period (e.g., several months), remove the batteries to prevent potential leakage and corrosion.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lantern does not turn on. | Batteries are dead or incorrectly installed. | Check battery polarity. Replace with fresh AAA batteries. |
| Light is dim or flickers. | Low battery power. Dirty battery contacts. | Replace batteries. Clean battery contacts with a dry cloth or cotton swab. |
| Water inside battery compartment. | Battery compartment not sealed properly. Exposure to excessive water. | Ensure battery compartment cover is securely closed. Dry the compartment thoroughly before reinserting batteries. Avoid submerging the lantern. |
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | BBM920 |
| Max Lumens | 125 lm |
| Max Runtime | 4 hours |
| Max Beam Distance | 53 meters |
| Battery Type | 3 x AAA (not included) |
| Water Resistance | IPX4 (Water Resistant) |
| Light Source Type | LED (8 Kong LEDs, 1 Cree LED) |
| Modes of Operation | High, Low, Strobe (Lantern), Flashlight |
| Material | Rubberized coating, high-performance plastic |
| Color | Black/Green |
| Item Weight | 3.8 Pounds |
9. Warranty and Support
For information regarding product warranty, technical support, or service, please refer to the contact details provided on the product packaging or visit the official Blackfire website. Keep your purchase receipt as proof of purchase for any warranty claims.
