1. Product Overview
The GE Appliances WB19K10044 Valve and Pressure Regulator is a genuine OEM (Original Equipment Manufacturer) part designed for GE gas range, stove, and oven appliances. This component is crucial for controlling the gas supply to the oven burners, ensuring safe and efficient operation. It is also referred to as the Gas Pressure Regulator and Oven Safety Valve Assembly.
Image 1: Front view of the GE WB19K10044 Valve and Pressure Regulator. This image displays the main body of the regulator with its gas inlet and outlet connections, along with the electrical terminals for the safety valve.
This high-quality part is manufactured with premium materials for durability and an exact fit, ensuring reliable performance in your appliance. Choosing genuine GE Appliances parts helps maintain the integrity and functionality of your equipment.
2. Safety Information
WARNING: Before attempting any installation, repair, or maintenance on your gas appliance, it is imperative to disconnect the appliance from all utilities, including electricity and gas supply. Failure to do so can result in serious injury, property damage, or death.
This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Always wear appropriate personal protective equipment, such as gloves and eye protection, during installation. If you are unsure about any step, consult a qualified service technician.
3. Installation
Installation of the WB19K10044 Valve and Pressure Regulator requires careful attention to detail and adherence to safety protocols. It is recommended to refer to the specific service manual for your GE gas range/stove/oven model for detailed, step-by-step instructions, as procedures may vary slightly between models.
General Installation Steps:
- Disconnect Utilities: Turn off the gas supply to the appliance at the main shut-off valve and unplug the appliance from the electrical outlet.
- Access the Component: Depending on your appliance model, you may need to remove the back panel, top panel, or other access covers to reach the existing valve and pressure regulator.
- Identify and Document Connections: Carefully note or photograph the existing gas line connections and electrical wiring to the old regulator. This will aid in correct reassembly.
- Remove Old Regulator: Disconnect the gas lines and electrical wires from the old valve and pressure regulator. Carefully unmount the old component from its position.
- Install New Regulator: Mount the new GE WB19K10044 Valve and Pressure Regulator in the same location as the old one. Ensure all mounting hardware is securely fastened.
- Connect Gas Lines: Reconnect the gas lines to the new regulator. Use appropriate thread sealant on gas pipe threads to prevent leaks.
- Connect Electrical Wires: Reconnect the electrical wires to the safety valve terminals as documented earlier.
- Check for Gas Leaks: After reconnecting gas lines, turn on the main gas supply. Apply a leak detection solution (soapy water) to all gas connections. Bubbles indicate a leak. If a leak is detected, immediately turn off the gas supply and tighten connections until no bubbles appear.
- Restore Utilities and Test: Plug the appliance back into the electrical outlet. Test the oven burner operation to ensure proper ignition and flame characteristics.
Image 2: Side view of the GE WB19K10044 Valve and Pressure Regulator. This angle highlights the overall assembly and the connection points for the gas lines and electrical components.
4. Operation
The WB19K10044 Valve and Pressure Regulator operates automatically to manage the gas flow to your oven burners. When the oven is turned on and a temperature is set, the safety valve within the assembly opens to allow gas to flow to the burner. The pressure regulator ensures that the gas is delivered at a consistent and safe pressure for optimal combustion and heating.
This component is not user-adjustable in terms of gas pressure settings. Its function is to maintain the factory-specified pressure for your appliance.
5. Maintenance
The GE WB19K10044 Valve and Pressure Regulator is designed to be a maintenance-free component. Regular cleaning or lubrication is not required. If the part is functioning correctly, no intervention is needed.
Periodically inspect the gas connections around the regulator for any signs of corrosion or damage. If any issues are observed, or if you suspect a gas leak, immediately turn off the gas supply and contact a qualified service technician.
6. Troubleshooting
If your oven is experiencing issues related to gas supply, the valve and pressure regulator might be a contributing factor. Below are common symptoms and potential troubleshooting steps:
- Oven Not Heating or Heating Slowly: This could indicate that the safety valve is not opening correctly or the regulator is not allowing sufficient gas flow.
- Gas Smell: A persistent gas smell, especially when the oven is in use, suggests a gas leak. Immediately turn off the gas supply and contact a professional. Do not attempt to operate the appliance.
- Uneven or Weak Oven Flame: If the oven burner flame is inconsistent, too small, or too large, the pressure regulator may not be maintaining the correct gas pressure.
- Oven Not Igniting: While often an igniter issue, a faulty safety valve that fails to open can also prevent gas from reaching the igniter.
Important: Due to the involvement of gas, any troubleshooting beyond visual inspection and leak detection should be performed by a qualified and certified appliance repair technician. Do not attempt complex repairs involving gas lines or internal valve components yourself.
Image 3: Top-down view of the GE WB19K10044 Valve and Pressure Regulator. This view provides a clear perspective of the overall assembly, including the gas connections and the safety valve mechanism.
7. Specifications
| Brand | GE |
| Model Number | WB19K10044 |
| Item Type Name | Valve + Pressure Regulator |
| Valve Type | Pressure Regulator |
| Item Dimensions (L x W x H) | 8 x 6 x 3 inches |
| Item Weight | 1.1 Pounds |
| Included Components | Single GE WB19K10044 Valve + Pressure Regulator for Gas Range/Stove/Ovens |
8. Compatible Models
The GE WB19K10044 Valve and Pressure Regulator is compatible with a wide range of GE gas range/stove/oven models. A partial list of compatible models includes:
- JGBS18GER3SA
- JGBS19GER3SA
- JGBS18DEN6BB
- JGBS23SEH4SS
- JGBS19DEN6BB
- JGBS18DEN6CC
- JGBS18DET1BB
- JGBS23SEM4SS
- JGBS23CEH3CC
- JGBS23DEM6BB
- JGBS22BEH3WH
- JGBS18DET1CC
- JGBS23DEM6CC
- JGBS18DEN4WW
- JGBS23DET1BB
- JGBS21HEH1WW
- JGBS23DET1CC
- JGBS23WEH1WW
- JGBS22WEK1WW
- JGBS23DEM4WW
- JGBS18GER4SA
- JGBS19GER4SA
- JGBS18DEN7BB
- JGBS19DEN7BB
- JGBS23BEH1BB
- JGBS18DEN7CC
- JGBS23SEM5SS
- JGBS23CEH4CC
- JGBS23DEM7BB
- JGBS22BEH4WH
- JGBS18MEN4BS
- JGBS23DEM7CC
- JGBS22BEH1CT
- JGBS18DEN5WW
- JGBS23DET2BB
- JGBS21HEH2WW
- JGBS19DEN5WW
- JGBS23DET2CC
- JGBS23WEH2WW
- JGBS23DEM5WW
- JGBS18SER1SS
- JGBS23SEH1SS
- JGBS18SET1SS
- JGBS19DEN8BB
- JGBS19SER1SS
- JGBS23BEH2BB
- JGBS23SEM6SS
- JGBS18MEN5BS
- JGBS23SER1SS
- JGBS19MEN5BS
Always verify compatibility with your specific appliance model number before purchasing or installing any replacement part.
9. Warranty and Support
As a Genuine GE Appliances part, the WB19K10044 Valve and Pressure Regulator is backed by GE Appliances' quality standards. Specific warranty details for replacement parts may vary. Please refer to the warranty information provided with your original appliance or contact GE Appliances customer support for current warranty terms.
For further assistance, technical support, or to locate a certified service technician, please visit the official GE Appliances website or contact their customer service department.
GE Appliances Official Website: www.geappliances.com