1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Apollo ASI 0483 Toilet Tissue and Seat Cover Dispenser with Sanitary Napkin Disposal. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the unit. Retain this manual for future reference.
2. Safety Instructions
- Professional installation is recommended to ensure secure mounting and compliance with local building codes.
- Always wear appropriate personal protective equipment (PPE) during installation, including safety glasses and gloves.
- Ensure the mounting surface is structurally sound and capable of supporting the dispenser's weight when fully loaded.
- Keep all tools and small parts out of reach of children during installation.
- Do not attempt to modify the dispenser. Use only genuine replacement parts if necessary.
- Dispose of waste materials, including sanitary napkins, according to local regulations.
3. Package Contents
Verify that all components are present before beginning installation:
- ASI 0483 Dispenser Unit (1)
- Mounting Hardware (screws, anchors) (1 set)
- Key for Locking Mechanism (1)
4. Setup and Installation
4.1 Mounting Location
Select a suitable wall location in the restroom that allows for easy access for users and maintenance personnel. Ensure adequate clearance for opening the unit for refilling and servicing. Avoid mounting directly above electrical outlets or in areas prone to excessive moisture.
4.2 Installation Steps
- Prepare the Wall: Hold the dispenser against the desired mounting surface. Use a pencil to mark the locations for the mounting holes. Ensure the dispenser is level before marking.
- Drill Pilot Holes: Using an appropriate drill bit for your wall type (e.g., masonry bit for concrete, wood bit for studs), drill pilot holes at the marked locations. If using wall anchors, ensure the hole size matches the anchor specifications.
- Insert Anchors (if needed): If drilling into drywall or hollow walls, insert the appropriate wall anchors into the pilot holes.
- Mount the Dispenser: Align the dispenser's mounting holes with the drilled holes/anchors. Insert the provided screws and tighten them securely. Do not overtighten, as this may damage the dispenser or the wall.
- Test Security: Gently pull on the dispenser to ensure it is firmly attached to the wall and does not wobble.
Figure 1: The ASI 0483 Dispenser unit, designed for wall mounting, featuring separate compartments for toilet tissue, seat covers, and a sanitary napkin disposal chute.
5. Operating Instructions
5.1 Loading Toilet Tissue
- Unlock the dispenser using the provided key and open the front panel.
- Place standard coreless toilet tissue rolls onto the designated spindles within the tissue compartment. Ensure the tissue feeds smoothly through the dispensing slot.
- Close the front panel and lock it securely.
5.2 Loading Seat Covers
- Unlock the dispenser using the provided key and open the front panel.
- Insert a fresh stack of standard toilet seat covers into the seat cover compartment. Ensure they are aligned correctly for proper dispensing.
- Close the front panel and lock it securely.
5.3 Using Sanitary Napkin Disposal
The dispenser features an integrated chute for sanitary napkin disposal. Users should place used sanitary products into the designated opening. The internal receptacle should be emptied regularly by maintenance personnel.
6. Maintenance
6.1 Cleaning
Regular cleaning helps maintain hygiene and appearance:
- Wipe the exterior surfaces with a soft, damp cloth and a mild, non-abrasive cleaner.
- Avoid using harsh chemicals, abrasive pads, or solvents, as these can damage the finish.
- Ensure the unit is dry after cleaning to prevent water spots.
6.2 Refilling and Emptying
- Toilet Tissue: Monitor tissue levels and refill as described in Section 5.1.
- Seat Covers: Monitor seat cover levels and refill as described in Section 5.2.
- Sanitary Napkin Disposal: Unlock the unit, open the front panel, and remove the internal receptacle. Empty contents into a waste bin lined with a suitable bag. Clean the receptacle as needed before returning it to the dispenser. Close and lock the unit.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Tissue or seat covers not dispensing | Empty compartment, jammed paper, incorrect loading. | Refill tissue/covers. Check for obstructions and clear. Ensure paper is loaded correctly according to Section 5. |
| Dispenser door will not close/lock | Obstruction, damaged lock mechanism, overfilled compartments. | Check for anything blocking the door. Inspect the lock for damage. Ensure compartments are not overfilled. |
| Unit feels loose on wall | Mounting screws are loose, wall anchors failing. | Tighten mounting screws. If problem persists, inspect wall anchors and consider re-mounting with stronger anchors or in a more secure location. |
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Apollo |
| Manufacturer | ASI |
| Model | 0483 |
| Finish Type | Satin Stainless Steel |
| Item Weight | 27.5 Pounds |
| Shape | Rectangular |
| Style | Modern |
| Number of Items | 1 |
| Date First Available | May 20, 2010 |
9. Warranty and Support
This Apollo ASI 0483 dispenser is covered by the manufacturer's standard warranty. Please refer to the warranty documentation provided at the time of purchase for specific terms and conditions. For technical support, replacement parts, or warranty claims, please contact your authorized Apollo distributor or the manufacturer directly. Contact information can typically be found on the manufacturer's official website or on your purchase receipt.
