KeylessOption 3-Button Key Fob Remote Control Replacement

Introduction

This manual provides comprehensive instructions for the installation, programming, and maintenance of your KeylessOption 3-Button Key Fob Remote Control Replacement. This product is designed to replace your original factory remote with a reliable and functional alternative. Please read all instructions carefully before proceeding.

Package Contents

Verify that all items are present in your package:

• KeylessOption 3-Button Remote Control(s)
• CR2032 Lithium Battery(s) (pre-installed)
• Key Ring Loops
• Programming Instructions (included with product)

Figure 1: Contents of the KeylessOption Key Fob package. Includes remote controls, pre-installed batteries, and key ring loops.

Vehicle Compatibility

This key fob is compatible with specific vehicle models and years. Ensure your vehicle is listed below before attempting to program the remote. This remote is a replacement for OEM part numbers LHJ011, 15186200, 15186201, 15132197, 15132198, 10377295, 22730827, 15186203, & 21997127 (FCC ID: LHJ011).

• Cadillac: Escalade (2003-2007)
• Chevrolet: Avalanche (2003-2007), Silverado (2003-2007), Suburban (2003-2007), Tahoe (2003-2007)
• GMC: Sierra (2003-2007), Yukon (2003-2007)
• Hummer: H2 (2003-2007)

Figure 2: Visual guide to self-programming and compatible vehicle models.

Key Fob Features

Your KeylessOption remote features three distinct buttons for convenient vehicle control:

• Lock Button: Secures all vehicle doors.
• Unlock Button: Unlocks all vehicle doors.
• Panic Button: Activates the vehicle's alarm system for emergency situations.

Figure 3: Front view of the key fob, highlighting the Lock, Unlock, and Panic buttons.

Programming Instructions

This key fob is designed for self-programming. The exact steps may vary slightly by vehicle model and year. Always refer to your vehicle's owner's manual for the most accurate programming procedure. A common procedure for compatible GM vehicles is as follows:

1. Ensure all vehicle doors are closed.
2. Sit in the driver's seat.
3. Insert your vehicle's ignition key into the ignition.
4. Hold down the UNLOCK button on the driver's side door panel.
5. While holding the UNLOCK button, cycle the ignition key from OFF to ON and back to OFF two times. Do not start the engine.
6. Release the UNLOCK button. The vehicle's door locks should cycle (lock and unlock) to indicate that the vehicle is now in programming mode.
7. On the new key fob, simultaneously press and hold the LOCK and UNLOCK buttons for approximately 15 seconds. The vehicle's door locks should cycle again to confirm successful programming of the first remote.
8. If programming additional remotes (including existing ones), immediately repeat step 7 for each additional remote. All remotes must be programmed during the same session.
9. To exit programming mode, turn the ignition key to the ON position, then remove the key. The door locks should cycle one last time.
10. Test all programmed remotes to ensure full functionality.

Important Note for Multiple Fobs: If you are programming more than one key fob, ensure you program all of them during the same session. If you program one and then exit programming mode before programming the others, the previously programmed fobs may become unprogrammed.

Battery Replacement

The key fob uses a CR2032 lithium battery. If the remote's range decreases or it stops responding, the battery may need replacement.

1. Locate the small notch on the side of the key fob.
2. Using a small flat-head screwdriver or a coin, carefully pry open the two halves of the key fob at the notch.
3. Remove the old CR2032 battery. Note the orientation (+/-) of the battery.
4. Insert a new CR2032 battery with the positive (+) side facing up.
5. Carefully snap the two halves of the key fob back together until they are securely closed.
6. Test the key fob's functionality.

Figure 4: Back of the key fob, indicating the opening point for battery replacement.

Specifications

Troubleshooting

• Fob not responding after programming:
  • Ensure all steps of the programming procedure were followed precisely.
  • If programming multiple fobs, ensure all were programmed in the same session. Reprogram all fobs if necessary.
  • Check the battery. Replace if necessary, ensuring correct polarity.
  • Verify vehicle compatibility.
• Reduced range:
  • The battery may be low. Replace the CR2032 battery.
  • Ensure there are no obstructions or strong radio interference between the fob and the vehicle.
• Buttons are stiff or unresponsive:
  • Check for debris or damage around the buttons.
  • Ensure the fob is properly assembled after battery replacement.

Warranty and Support

Your KeylessOption key fob comes with a 90-day warranty from the date of purchase. This warranty covers manufacturing defects and ensures quality and peace of mind. If you experience any defects or issues within this period, please contact KeylessOption customer support for assistance or a replacement.

For further support or to inquire about specific programming details for your vehicle, please refer to your vehicle's owner's manual or visit the official KeylessOption website.