User Manual: Vehicle Car GPS Tracker TK103A

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your TheCoolCube TK103A Vehicle Car GPS Tracker. This device is designed to offer security, tracking, monitoring, emergency alarms, and management capabilities for various vehicles.

Important Note:

As of December 6, 2023, the previous platform "TrackerHome" has been updated to the new "BAANOOL IOT" (www.baanooliot.com). Existing TrackerHome users may need to register a new account and transfer their device to the BAANOOL IOT platform.

Product Overview

The TK103A GPS Tracker integrates security, tracking, monitoring, and management functions. It operates on GSM/GPRS networks and utilizes GPS satellite positioning for accurate tracking. The device supports 9-36V power input, making it suitable for various vehicles including buses, taxis, trucks, and personal cars.

Image: Top view of the TK103A GPS Tracker, showing the "GPS TRACKER" logo and antenna ports.

Image: Angled view of the TK103A GPS Tracker, displaying the IMEI and serial number labels on the side.

Key Features:

• Built-in GPS and GSM antenna.
• Supports GPS and LBS (Location Based Service) dual tracking solutions.
• SD card slot for data storage.
• Anti-theft alarm functions.
• Real-time tracking via SMS or internet.
• Supports up to 5 administrator numbers for monitoring.

Package Contents

Verify that all items listed below are included in your package:

• 1x Genuine Box
• 1x GPS TRACKER TK103A Unit
• 1x GPS Antenna (3 meters long)
• 1x GSM Antenna
• 1x Plug 10 pin Harness
• 1x Relay
• 1x Microphone
• 1x User Manuals
• 1x CD (for software/drivers)

Image: All components included in the TK103A GPS Tracker package, laid out for inspection.

Image: The TK103A GPS Tracker and its accessories, including the user manual, shown alongside its retail packaging.

Setup and Installation

Proper installation is crucial for the optimal performance of your GPS tracker. It is recommended to have this device installed by a qualified professional.

Component Identification:

Image: Detailed diagram illustrating the various components of the TK103A GPS Tracker, including GSM antenna connector, SIM card slot, MicroSD slot, microphone jack, GPS antenna connector, shock sensor port, GSM/GPS LED, backup battery switch, remote controller antenna (optional), and harness port. A wiring diagram for vehicle integration is also shown.

1. SIM Card Insertion: Open the SIM card slot and insert a valid GSM SIM card with GPRS data enabled. Ensure the SIM card is activated and has sufficient balance for SMS and data services.
2. Antenna Connection: Connect the GPS antenna and GSM antenna to their respective ports on the device. Ensure they are securely fastened.
3. Wiring Harness Connection: Connect the 10-pin wiring harness to the device. The harness includes connections for power (9-36V), ACC (ignition), relay for fuel/power cut-off, siren, and door triggers. Refer to the wiring diagram for precise connections.
   • Red Wire: Connect to constant 12V/24V power supply.
   • Black Wire: Connect to vehicle ground.
   • White Wire (ACC): Connect to ignition switch (Accessory power).
   • Orange Wire (Siren): Connect to siren positive.
   • Green Wire (+ Door Trigger): Connect to positive door trigger.
   • Blue Wire (- Door Trigger): Connect to negative door trigger.
   • Yellow Wires (Relay): Connect to the fuel pump or engine power line via the provided relay for remote cut-off functionality.
4. Microphone Connection: If desired, connect the microphone to the microphone jack for voice monitoring.
5. SD Card Insertion: Insert a MicroSD card into the slot for data logging (optional).
6. Power On: After all connections are made, turn on the device using the backup battery switch (if applicable) or by connecting to vehicle power. The GSM/GPS LEDs will indicate status.

Optimal Installation Locations:

Choose a hidden location within the vehicle to prevent tampering and ensure good GPS/GSM signal reception. Avoid placing the device directly under metal objects.

Image: Visual guide showing recommended installation spots for the TK103A GPS Tracker in automobiles (under dashboard, glove compartment, trunk), trucks (inside plastic plate, car roof, windshield), motorcycles (tail light interior, plastic parts, headlight cover), and electric motorcycles (under seat).

• Automobile: Below the front windshield, under the steering wheel, upper part of the glove compartment. Trunk is an optional location.
• Truck: Inside the plastic plate under rear, inside the car roof, inside the front windshield.
• Motorcycle: Tail light interior, inside plastic parts, inside the headlight cover, near the table.
• Electric Motorcycle: Under the seat.

Attention:

The installation must be positive up and no metal objects cover, and pay attention to waterproof measures!

Operating Instructions

The TK103A can be operated via SMS commands or through a web-based tracking platform (BAANOOL IOT).

Initial Configuration (SMS Commands):

Before using the device, you need to configure it. All SMS commands should be sent from an authorized phone number to the SIM card number inside the tracker.

1. Activate Device: Send "begin123456" to the tracker's SIM card number. The tracker should reply with "begin ok!".
2. Change Password: For security, change the default password. Send "password123456 newpassword" (replace "newpassword" with your desired 6-digit password).
3. Set Admin Numbers: Add up to 5 administrator phone numbers that can control the device. Send "admin[password] [phone number]" (e.g., "admin123456 1234567890"). Repeat for each admin number.
4. Set APN: Configure the Access Point Name (APN) for GPRS data. This is crucial for web tracking. Send "apn[password] [APN name]" (e.g., "apn123456 internet"). Consult your SIM card provider for the correct APN.
5. Set IP and Port (for BAANOOL IOT): Send "adminip[password] [IP address] [port]" (e.g., "adminip123456 193.193.165.166 20462"). Refer to BAANOOL IOT documentation for the correct IP and port.
6. Enable GPRS: Send "gprs[password]" to enable GPRS data transmission.
7. Set Time Zone: Send "time zone[password] [offset]" (e.g., "time zone123456 -5" for EST).

Tracking and Monitoring:

• Single Location Query: Call the tracker's SIM card number or send "fix030s001n[password]". The tracker will reply with a Google Maps link showing its current location.
• Continuous Tracking: Send "fix[time interval]s***n[password]" (e.g., "fix010s***n123456" for continuous reports every 10 seconds).
• Web Platform Tracking: Log in to the BAANOOL IOT platform (www.baanooliot.com) using your registered account. Add your device using its IMEI number (send "imei[password]" to get it). You can then view real-time location, historical routes, and set geofences.
• Voice Monitoring: Call the tracker's SIM card number from an authorized phone number to listen to the surroundings (if microphone is connected).

Alarm Functions:

• SOS Alarm: If an SOS button is connected (optional), pressing it will send an SOS alert to all admin numbers.
• Geo-fence Alarm: Set a virtual boundary via the web platform. If the vehicle enters or exits this area, an alert will be sent.
• Movement Alarm: Send "move[password] [distance]" (e.g., "move123456 200" for 200 meters). If the vehicle moves beyond the set distance, an alarm is triggered.
• Overspeed Alarm: Send "speed[password] [speed limit]" (e.g., "speed123456 120" for 120 km/h). An alert is sent if the vehicle exceeds the set speed.
• Low Battery Alarm: The device will send an alert when its internal backup battery is low.
• External Power Off Alarm: An alert is sent if the main power supply to the device is disconnected.

Remote Control Functions:

• Remote Engine Cut-off: Send "stop[password]" to cut off the fuel/power supply to the vehicle. Send "resume[password]" to restore it. This function requires proper relay installation.
• Arm/Disarm: Send "arm[password]" to arm the alarm system. Send "disarm[password]" to disarm it.

Maintenance

To ensure the longevity and reliable operation of your TK103A GPS Tracker, follow these maintenance guidelines:

• Regular Cleaning: Keep the device clean and free from dust and debris. Use a soft, dry cloth for cleaning. Do not use liquid cleaners.
• Environmental Protection: Avoid exposing the device to extreme temperatures, direct sunlight for prolonged periods, or high humidity. Ensure it is installed in a dry location.
• Secure Installation: Periodically check that the device and its antennas are securely mounted and that all wiring connections are firm. Vibrations can loosen connections over time.
• SIM Card and GPRS: Ensure the SIM card has sufficient credit/data plan and is active. GPRS connectivity is essential for web-based tracking.
• Firmware Updates: Check the manufacturer's website or the BAANOOL IOT platform for any available firmware updates. Follow instructions carefully if an update is necessary.
• Battery Health: The device has a built-in backup battery. While designed for longevity, extreme temperatures can affect its performance. If the low battery alarm is frequent, consider professional inspection.

Troubleshooting

If you encounter issues with your TK103A GPS Tracker, refer to the following common problems and solutions:

If the problem persists after attempting these solutions, please contact customer support.

Specifications

Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact TheCoolCube customer service.

Online Platform Support: For issues related to the tracking platform, please visit www.baanooliot.com.

Manufacturer: Coban

Brand: TheCoolCube