Introduction
This manual provides comprehensive instructions for the setup, operation, and maintenance of your Wildgame Innovations Buck Commander Nano 10 Hunting Trail Camera. Please read this manual thoroughly before using the camera to ensure optimal performance and longevity.
The Buck Commander Nano 10 is a compact and robust trail camera designed for outdoor surveillance. It features advanced imaging capabilities and a durable, weather-resistant design suitable for various environmental conditions.
Product Overview
Figure 1: Front view of the Wildgame Innovations Buck Commander Nano 10 Hunting Trail Camera, showcasing its compact design, integrated lens, infrared LEDs, and the Buck Commander logo.
The Buck Commander Nano 10 is engineered for discreet and effective wildlife monitoring. Key features include:
- 10 MP Micro Digital Trail Camera: Captures high-resolution still images.
- 36 High Intensity LEDs: Provides an 80 ft flash range for clear night vision.
- Tree Bark Finish: Blends seamlessly with natural environments, enhancing concealment.
- 1 Second Trigger Speed: Ensures quick capture of moving subjects.
- HD 720p Video Capabilities: Records video clips up to 30 seconds in length.
- Water Resistant and Weather Endurable: Designed to withstand various outdoor conditions.
- SD/SDHC Card Support: Compatible with cards up to 32GB (not included).
- External Battery Port: Allows for extended power options.
Setup
1. Battery Installation
- Open the camera housing latch.
- Locate the battery compartment.
- Insert 4 AA batteries (not included) into the compartment, ensuring correct polarity (+/-).
- Close the battery compartment securely.
2. SD Card Insertion
- With the camera housing open, locate the SD card slot.
- Insert an SD or SDHC card (up to 32GB, not included) into the slot until it clicks into place. Ensure the card is inserted in the correct orientation.
- To remove, gently push the card in until it springs out.
3. Mounting the Camera
The camera comes with bungee cords for mounting. Follow these steps:
- Select a suitable tree or post for mounting.
- Thread the bungee cords through the mounting slots on the back of the camera.
- Securely wrap the bungee cords around the tree/post and fasten them.
- Adjust the camera angle to cover the desired area.
Operating Instructions
Powering On/Off
- To power on, slide the power switch to the "ON" position.
- To power off, slide the power switch to the "OFF" position.
Setting Date and Time
Refer to the included Flextime CD and USB cord for detailed instructions on setting the date and time, and configuring other camera settings via a computer. The camera's small display may require careful viewing.
Photo and Video Modes
The Buck Commander Nano 10 supports both still photo and HD 720p video capture. Specific mode selection and advanced settings are typically managed through the Flextime software on your computer.
Viewing Captured Media
To view photos and videos, remove the SD card from the camera and insert it into a compatible card reader connected to a computer or a device with an SD card slot. The files will be accessible in standard image and video formats.
Maintenance
- Cleaning: Use a soft, dry cloth to clean the camera lens and housing. Avoid abrasive cleaners or solvents.
- Battery Replacement: Replace batteries when the low battery indicator appears or when performance degrades. Always use fresh, high-quality AA batteries.
- SD Card Management: Regularly format your SD card using the camera's utility (if available) or a computer to ensure optimal performance and prevent data corruption. Back up important files before formatting.
- Storage: When not in use for extended periods, remove batteries and store the camera in a cool, dry place away from direct sunlight.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Camera not powering on. | Dead or incorrectly installed batteries. | Check battery polarity; replace with fresh batteries. |
| Poor image/video quality. | Dirty lens; low light conditions; incorrect settings. | Clean the lens; ensure adequate lighting; verify settings via Flextime software. |
| Camera not recording. | Full or corrupted SD card; incorrect mode selection. | Format or replace SD card; ensure camera is in active recording mode. |
| Display difficult to read. | Small display size; viewing angle. | This is a known characteristic of the compact design. Adjust viewing angle or use Flextime software for detailed settings. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | P10i20 |
| Effective Still Resolution | 10 MP |
| Video Capture Resolution | 720p (HD) |
| Flash Range | 80 ft (36 high intensity LEDs) |
| Trigger Speed | 1 second |
| Memory Card Support | SD/SDHC up to 32GB |
| Power Source | 4 AA Batteries (not included) |
| Connectivity | USB (for Flextime CD) |
| Water Resistance Level | Water Resistant (IP54) |
| Dimensions (L x W x H) | 9.5 x 5.5 x 2.88 inches |
| Weight | 1.1 Pounds |
| Special Features | Flextime, Time-Lapse Technology, External Battery Port |
Warranty and Support
For warranty information and technical support, please refer to the documentation included with your product packaging or visit the official Wildgame Innovations website. Keep your purchase receipt for warranty claims.
Manufacturer: Wildgame Innovations - BA Products
Date First Available: February 27, 2014