Ecolink Z-Wave Tilt Sensor (TILT-ZWAVE2-ECO) Instruction Manual

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Ecolink Z-Wave Tilt Sensor (TILT-ZWAVE2-ECO). This device is designed to monitor the tilt status of objects, primarily garage doors, and communicate this status wirelessly via Z-Wave technology to a compatible smart home hub. Ensure you read these instructions thoroughly before installation and use.

Product Overview

Image 1: Front view of the Ecolink Z-Wave Tilt Sensor. The sensor is a compact, white rectangular device with a small black indicator light on its front surface.

Key Features

• Reliable Tilt Detection: Utilizes gold-plated components for consistent performance.
• Z-Wave Compatibility: Works with most Z-Wave certified smart home hubs.
• Long Battery Life: Designed for up to five years of operation on a single CR123 battery.
• Discrete Design: Compact form factor for unobtrusive installation.
• External Contact Input: Allows for connection of an external wired sensor.
• Easy Installation: Includes flush mount bracket and adhesive options.

Package Contents

• Ecolink Z-Wave Tilt Sensor (TILT-ZWAVE2-ECO)
• CR123 Lithium Battery (pre-installed or separate)
• Mounting Bracket
• Mounting Screws and Anchors
• Double-Sided Adhesive Tape
• Instruction Manual (this document)

Setup

1. Battery Installation

1. Remove the back cover of the sensor by gently prying it open or sliding it off, depending on the model.
2. Insert the included CR123 lithium battery, observing the correct polarity (+/-).
3. Replace the back cover, ensuring it clicks securely into place. The sensor's LED may flash briefly to indicate power.

2. Z-Wave Inclusion (Pairing)

To integrate the sensor into your Z-Wave network, follow these steps:

1. Place your Z-Wave hub into inclusion (pairing) mode. Refer to your hub's instruction manual for specific steps.
2. With the sensor powered on, press the tamper switch (located inside the sensor, often a small button or lever) once. The sensor's LED will flash to indicate it is attempting to pair.
3. If inclusion is successful, the LED will stop flashing, and your Z-Wave hub should confirm the new device.
4. If inclusion fails, the LED may flash rapidly or remain off. Try repeating the process or performing an exclusion first.

3. Z-Wave Exclusion (Unpairing)

To remove the sensor from your Z-Wave network:

1. Place your Z-Wave hub into exclusion (unpairing) mode. Refer to your hub's instruction manual for specific steps.
2. Press the tamper switch on the sensor once. The sensor's LED will flash to indicate it is attempting to unpair.
3. If exclusion is successful, the LED will stop flashing, and your Z-Wave hub should confirm the device has been removed.

4. Mounting the Sensor

The sensor can be mounted using screws or double-sided adhesive tape. For garage doors, mount the sensor on the top panel of the garage door, ensuring it changes orientation (tilts) when the door opens or closes.

• Location: Choose a location on the top panel of the garage door where the sensor will clearly tilt when the door moves.
• Adhesive Mounting: Clean the mounting surface thoroughly. Apply the double-sided adhesive tape to the back of the sensor or mounting bracket and firmly press it onto the desired location for at least 30 seconds.
• Screw Mounting: Use the included mounting bracket as a template. Mark the screw holes, drill pilot holes if necessary, and secure the bracket with the provided screws. Attach the sensor to the bracket. For added security, a small security screw may be used to fasten the sensor to the bracket (refer to the sensor's internal design for the security screw location).
• Orientation: Ensure the sensor is mounted in an orientation where its internal tilt mechanism can accurately detect the open and closed states of the garage door. Typically, this means mounting it vertically when the door is closed, so it becomes horizontal when the door is open.

Operating Instructions

Tilt Detection

The Ecolink Z-Wave Tilt Sensor detects changes in its physical orientation. When mounted correctly on a garage door, it will report an "open" status to your Z-Wave hub when the door is open (sensor is horizontal) and a "closed" status when the door is closed (sensor is vertical). This status is communicated wirelessly to your Z-Wave network, allowing for automation and notifications.

External Contact Input

The sensor includes an external contact input. This allows you to connect a separate wired normally-closed (NC) or normally-open (NO) contact sensor (e.g., a magnetic reed switch) to the tilt sensor. When the external contact changes state, the tilt sensor will report this status to your Z-Wave hub. This feature can be used for monitoring a secondary point or for applications where a tilt sensor is not suitable.

• To use the external input, connect the two wires from your external contact sensor to the designated terminals inside the Ecolink Tilt Sensor.
• Refer to your Z-Wave hub's documentation for configuring how the external input reports its status.

Maintenance

Battery Replacement

The Ecolink Z-Wave Tilt Sensor uses one CR123 lithium battery. When the battery level is low, your Z-Wave hub should report a low battery warning. To replace the battery:

1. Remove the sensor from its mounting bracket or detach it from the adhesive.
2. Open the back cover of the sensor.
3. Carefully remove the old CR123 battery.
4. Insert a new CR123 lithium battery, ensuring correct polarity.
5. Replace the back cover and re-mount the sensor.
6. It may be necessary to wake up the sensor or refresh its status on your Z-Wave hub after battery replacement to update the battery level.

Note: Dispose of old batteries according to local regulations.

Troubleshooting

Specifications

Warranty and Support

Ecolink products are designed for reliability and performance. For specific warranty information, please refer to the warranty card included with your product or visit the official Ecolink website. For technical support, troubleshooting assistance, or further inquiries, please contact Ecolink customer service through their official channels.

Ecolink Official Website: Visit the Ecolink Store on Amazon