1. Introduction
Thank you for choosing the Klarstein St.Gallen Premium Automatic Watch Winder. This device is designed to keep your automatic watches wound and ready to wear, simulating the natural motion of a wrist. This manual provides essential information for the safe and efficient operation of your watch winder. Please read it thoroughly before use and retain it for future reference.
2. Safety Instructions
- Read all instructions carefully before operating the device.
- Keep the watch winder away from direct sunlight, high temperatures, and humidity.
- Do not expose the device to water or other liquids.
- Ensure the power adapter is compatible with your local power supply.
- Unplug the device from the power outlet when not in use or before cleaning.
- Do not attempt to disassemble or repair the unit yourself. Contact qualified service personnel.
- Keep out of reach of children.
3. Package Contents
Please check the package for the following items:
- Klarstein St.Gallen Premium Automatic Watch Winder
- Power Adapter (4V - 5A)
- User Manual
4. Product Overview
Familiarize yourself with the components of your watch winder:
Key Components:
- Watch Holders: Two rotating compartments for automatic watches.
- Viewing Window: Large transparent door for displaying watches.
- LED Lighting: Blue internal illumination.
- Power Switch (ON/OFF): Located on the rear panel.
- Mode Selector Switch (A/B/C/D): Located on the rear panel, for choosing rotation programs.
- DC Power Input: For connecting the power adapter.
5. Setup
5.1 Placement
Place the watch winder on a stable, flat surface. Ensure it is in a dry environment, away from direct heat sources or strong magnetic fields.
5.2 Power Connection
- Ensure the power switch on the rear panel is in the OFF position.
- Connect the provided power adapter to the DC power input port on the rear of the watch winder (refer to Figure 2).
- Plug the power adapter into a suitable electrical outlet.
5.3 Inserting Watches
- Open the front door of the watch winder.
- Gently place your automatic watch onto one of the watch holders. Ensure the watch is securely seated and will not fall off during rotation. The winder is suitable for watches with a strap length between 155 mm and 205 mm.
- Repeat for the second watch if desired.
- Close the front door securely.
6. Operating Instructions
6.1 Power On/Off
To turn the watch winder ON, flip the power switch on the rear panel to the ON position. To turn it OFF, flip the switch to the OFF position.
6.2 Selecting Rotation Modes
The Klarstein St.Gallen Premium offers four distinct rotation programs. Use the mode selector switch on the rear panel (refer to Figure 2) to choose the desired program. The blue LED lighting will activate when the winder is operating.
| Mode | Description | Cycle |
|---|---|---|
| A | Rotates clockwise. | Rotates for 2 minutes, rests for 6 minutes, then repeats. |
| B | Rotates counter-clockwise. | Rotates for 2 minutes, rests for 6 minutes, then repeats. |
| C | Rotates bi-directionally (alternating). | Rotates clockwise for 2 minutes, rests for 6 minutes, then rotates counter-clockwise for 2 minutes, rests for 6 minutes, then repeats. |
| D | Rotates bi-directionally (longer cycle). | Rotates clockwise for 5 minutes, then counter-clockwise for 5 minutes. This cycle repeats for 3 hours, followed by a 9-hour rest period, then repeats. |
Choose the mode that best suits the winding requirements of your specific automatic watch. Consult your watch's manufacturer for recommended winding specifications if unsure.
7. Maintenance
7.1 Cleaning
- Before cleaning, ensure the watch winder is unplugged from the power outlet.
- Wipe the exterior surfaces with a soft, dry, or slightly damp cloth.
- Do not use abrasive cleaners, solvents, or chemical sprays, as these may damage the finish.
- Clean the viewing window with a soft, lint-free cloth to avoid scratches.
7.2 Storage
If storing the watch winder for an extended period, unplug it, clean it, and store it in a cool, dry place, away from dust and direct sunlight.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Watch winder does not operate. | No power supply. | Check if the power adapter is securely plugged into the winder and the wall outlet. Ensure the power switch is ON. |
| Watch is not winding. | Incorrect rotation mode selected for the watch. | Refer to your watch's manual for its specific winding requirements (direction and Turns Per Day - TPD). Adjust the mode selector accordingly. |
| Unusual noise during operation. | Watch not properly seated or obstruction. | Ensure watches are securely placed and not touching the winder's interior. Check for any foreign objects. If noise persists, discontinue use and contact support. |
| LED light not working. | Winder is in a rest cycle or power issue. | The LED light activates during rotation. If the winder is rotating but the LED is off, check power connection or contact support. |
If the problem persists after attempting these solutions, please contact customer support.
9. Specifications
- Model Number: St.Gallen Premium
- Capacity: 2 Automatic Watches
- Rotation Modes: 4 (Clockwise, Counter-clockwise, Bi-directional alternating, Bi-directional with rest)
- Operating Temperature: 5°C to 40°C (41°F to 104°F)
- Power Supply: DC 4V - 5A (via included adapter)
- Dimensions (L x W x H): Approximately 19.2 x 14.1 x 24.3 cm (7.56 x 5.55 x 9.57 inches)
- Weight: Approximately 840 grams (1.85 lbs)
- Suitable Watch Strap Length: 155 mm to 205 mm
10. Disposal Notes
Do not dispose of this product with normal household waste. This device complies with the WEEE Directive (2012/19/EU). Dispose of the device through an approved disposal company or your municipal waste facility. Observe current regulations. In case of doubt, consult your waste disposal center.
11. Warranty and Support
Information regarding warranty terms and customer support contact details was not provided in the source data. Please refer to your purchase documentation or contact your retailer for specific warranty information and support inquiries.
