Faria 13795 Chesapeake Depth Sounder Thru-Hull Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Faria 13795 Chesapeake Depth Sounder Thru-Hull. This device is designed to provide accurate depth readings in various marine conditions, utilizing advanced microprocessor technology for reliable performance.

2. Safety Information

• Always disconnect power before performing any installation or maintenance.
• Ensure proper sealing of all thru-hull components to prevent water intrusion.
• Consult a qualified marine technician if you are unsure about any installation steps.
• This device is an aid to navigation and should not be used as the sole source of navigation information.

3. Package Contents

Verify that all items are present in the package:

• Faria 13795 Chesapeake Depth Sounder Display Unit
• Thru-Hull Transducer (Note: The included transducer is typically 1.5 inches. A 2-inch transducer may need to be purchased separately if required for your application.)
• Mounting Hardware
• Instruction Manual (this document)

4. Setup and Installation

Proper installation is crucial for accurate depth readings. This section outlines the general steps for installing the depth sounder and its thru-hull transducer.

4.1 Component Overview

Figure 1: Faria 13795 Depth Sounder display unit (left) and the thru-hull transducer (right). The display features an LCD screen, 'ON/OFF MODE' button, and up/down arrow buttons for navigation and settings adjustment.

4.2 Transducer Installation

1. Select Location: Choose a location on the hull that is free from turbulence, air bubbles, and obstructions. The transducer should be mounted in an area that remains submerged at all speeds.
2. Drill Hole: Carefully drill a hole of the appropriate diameter for the transducer shaft. Refer to the transducer's specific dimensions for precise hole size.
3. Apply Sealant: Apply a marine-grade sealant (e.g., 3M 5200) generously around the edge of the transducer flange that will contact the hull.
4. Insert Transducer: Insert the transducer from the outside of the hull into the drilled hole.
5. Secure Internally: From inside the boat, place the large rubber gasket around the transducer shaft, followed by the securing nut.
6. Tighten Nut: Hand-tighten the nut securely. Avoid over-tightening, which can damage the hull or transducer. Wipe away any excess sealant.
7. Route Cable: Route the transducer cable to the display unit, ensuring it is protected from abrasion and interference.

4.3 Display Unit Installation

1. Mounting Location: Select a suitable location on the dashboard or panel for the display unit, ensuring clear visibility and accessibility.
2. Cut Opening: Use the provided template (if applicable) to cut the appropriate size opening for the display unit.
3. Secure Display: Insert the display unit into the opening and secure it using the supplied mounting bracket and hardware.
4. Wiring:
   • Connect the transducer cable to the designated port on the display unit.
   • Connect the power wire (typically red) to a switched 12V DC power source.
   • Connect the ground wire (typically black) to a reliable ground point.
   • Ensure all connections are secure and properly insulated.

5. Operating Instructions

This section details how to operate your Faria Depth Sounder.

5.1 Power On/Off

• To power on the unit, press and hold the ON/OFF MODE button until the display illuminates.
• To power off the unit, press and hold the ON/OFF MODE button until the display turns off.

5.2 Basic Operation

• Upon powering on, the unit will typically display the current depth.
• The unit features automatic gain control to optimize depth readings in varying conditions.
• Backlighting is integrated for enhanced visibility, especially during low-light conditions.

5.3 Mode Selection and Settings

• Press the ON/OFF MODE button briefly to cycle through different display modes or access settings menus.
• Use the Up (▲) and Down (▼) arrow buttons to adjust values or navigate menu options.
• Keel Offset: This setting allows you to adjust the depth reading to compensate for the distance between the transducer and the bottom of your boat's keel. Consult your boat's specifications to determine the correct offset value.
• Deep and Shallow Water Alarms: Set desired depth thresholds for both deep and shallow water. The unit will provide audio and visual alarms when these thresholds are crossed.

6. Features

• Oversized Back-lit display for clear visibility in various lighting conditions.
• Audio and visual alarms for elevation (deep and shallow water).
• Programmable keel offset for accurate depth measurement relative to the keel.
• Automatic gain control for optimal performance across different bottom conditions.
• Depth capability: 3-199 feet (61 meters).

7. Maintenance

• Cleaning: Wipe the display unit with a soft, damp cloth. Avoid abrasive cleaners or solvents.
• Transducer Inspection: Periodically inspect the transducer for marine growth or damage. Clean gently with a soft brush if necessary. Ensure the transducer cable is free from kinks or damage.
• Connections: Check all electrical connections annually for corrosion or looseness.

8. Troubleshooting

9. Specifications

• Model: 13795
• Brand: Faria
• Depth Capability: 3-199 feet (61 meters)
• Material: Plastic
• Item Weight: Approximately 1 Pound
• UPC: 759266137950
• Power Requirement: 12V DC (typical marine electrical system)
• Display: Back-lit LCD

10. Warranty and Support

Faria products are manufactured to high standards. For specific warranty details, please refer to the warranty card included with your product or visit the official Faria Beede Instruments website. For technical support or service inquiries, please contact Faria customer service directly.