Cornat AE70100 Dish Shower Hose User Manual

Product Overview

The Cornat AE70100 is a high-quality stainless steel rinse spray hose designed for sink taps. It features a silicon hose and is tested for W270 – KTW A standards, ensuring durability and safety for water applications. This hose is specifically designed with a 3/8 inch external thread on one end and a 1/2 inch internal thread on the other, with a total length of 125 cm.

Image: The Cornat AE70100 dish shower hose, showcasing its stainless steel construction and threaded connectors.

Specifications

Image: Diagram illustrating the 125 cm length of the Cornat AE70100 hose, confirming product dimensions.

Setup and Installation

Before beginning installation, ensure that the water supply to the sink tap is turned off. It is recommended to have a bucket or towel ready to catch any residual water.

1. Prepare Connections: Identify the 1/2 inch internal thread end of the new hose (typically connects to the spray head) and the 3/8 inch external thread end (typically connects to the tap's water supply line).
2. Remove Old Hose (if applicable): Carefully unscrew the old hose from both the spray head and the tap connection. Be mindful of any gaskets or washers that may fall out.
3. Connect to Spray Head: Screw the 1/2 inch internal thread end of the Cornat AE70100 hose onto the spray head. Hand-tighten first, then use a wrench for a snug fit, being careful not to overtighten. Ensure a washer is properly seated if required by your spray head.
4. Connect to Tap: Screw the 3/8 inch external thread end of the hose into the corresponding connection on your sink tap. Hand-tighten, then use a wrench for a secure connection. Verify that any necessary gaskets are in place to prevent leaks.
5. Check for Leaks: Slowly turn on the water supply to the sink tap. Inspect all connections for any signs of leaks. If leaks are present, gently tighten the connections further. Do not apply excessive force.

Image: A detailed view of the threaded connections on the Cornat AE70100 hose, showing the different thread sizes for proper installation.

Operating Instructions

The Cornat AE70100 dish shower hose operates in conjunction with your existing sink tap and spray head. Its primary function is to provide a flexible connection for extended reach and maneuverability during dishwashing or cleaning tasks.

• Extension and Retraction: Gently pull the spray head to extend the hose for use. When finished, guide the spray head back into its housing. Avoid forcing the hose or allowing it to kink, which can damage the internal silicon hose.
• Water Flow Control: Water flow and temperature are controlled by your sink tap's handles. The hose itself does not regulate water flow.
• Pressure Handling: The hose is designed to withstand a maximum pressure of 10 bars. Ensure your household water pressure does not exceed this limit for optimal performance and longevity.

Maintenance

Regular maintenance will help prolong the life of your Cornat AE70100 dish shower hose and ensure its continued functionality.

• Cleaning: Wipe the stainless steel exterior of the hose with a soft, damp cloth and mild soap as needed. Avoid abrasive cleaners or scouring pads, which can scratch the surface.
• Inspect Connections: Periodically check the connections at both ends of the hose for any signs of wear, corrosion, or leaks. Tighten connections if necessary, but do not overtighten.
• Prevent Kinking: Always allow the hose to retract smoothly without kinking. Kinks can stress the internal silicon hose and lead to premature failure.
• Water Quality: In areas with hard water, mineral deposits may accumulate over time. If you notice reduced water flow or spray pattern issues, consult your tap's manual for cleaning instructions for the spray head, as the hose itself is less prone to internal mineral buildup due to its design.

Troubleshooting

This section addresses common issues you might encounter with your dish shower hose.

Warranty and Support

For warranty information or technical support regarding your Cornat AE70100 dish shower hose, please refer to the original purchase documentation or contact Cornat customer service directly. Keep your proof of purchase for any warranty claims.

Manufacturer: Conmetall

Brand: Cornat

For further assistance, you may visit the official Cornat website or contact their support channels as listed on their packaging or website.