CISA DGT Vision Electronic Wall Safe - Model 182710300 User Manual

1. Introduction

Thank you for choosing the CISA DGT Vision Electronic Wall Safe, Model 182710300. This electronic wall safe is designed to provide secure storage for your valuables, offering robust protection combined with ease of use. This manual provides essential instructions for the proper installation, operation, and maintenance of your safe to ensure optimal performance and security. Please read this manual thoroughly before attempting to install or operate the safe.

Image 1.1: CISA DGT Vision Electronic Wall Safe with its door open, revealing the interior storage space and the electronic keypad on the door. The two steel locking bolts are visible.

2. Safety Information

To ensure safe operation and prevent injury or damage, please observe the following safety guidelines:

• Secure Installation: The safe must be securely anchored to a wall structure as instructed. Improper installation can compromise the safe's security and may lead to injury.
• Confidentiality: Keep your access codes confidential. Do not share them with unauthorized individuals.
• Battery Handling: Use only 1.5V alkaline batteries of the specified type. Do not mix old and new batteries, or different types of batteries. Replace all batteries at the same time.
• Children: Keep children away from the safe and its operating mechanisms.
• Maintenance: Do not attempt to repair or modify the safe yourself. Refer to qualified personnel for any service needs.

3. Package Contents

Upon unpacking, please verify that all components are present:

• CISA DGT Vision Electronic Wall Safe (Model 182710300)
• Instruction Manual (this document)
• Mounting hardware (typically bolts for wall installation)

Note: 1.5V alkaline batteries required for operation are not included and must be purchased separately.

4. Setup and Installation

The CISA DGT Vision is a wall-mounted safe designed for secure embedding into a wall. Professional installation is highly recommended to ensure maximum security and proper integration into your structure.

4.1. Site Selection

Choose a discreet and structurally sound location within a wall. Ensure there is sufficient depth and width in the wall cavity to accommodate the safe's dimensions.

4.2. Dimensions

The external dimensions of the safe are approximately 36 cm (Length) x 24 cm (Height) x 15 cm (Depth). The internal dimensions are approximately 34.2 cm (Length) x 22.2 cm (Height) x 10 cm (Depth).

Image 4.1: Dimensional diagram of the CISA DGT Vision Electronic Wall Safe, illustrating its external and internal measurements, including the removable internal shelf.

4.3. Installation Steps (General Guidelines)

1. Prepare Wall Cavity: Create an opening in the wall that is slightly larger than the safe's external dimensions to allow for proper embedding and finishing.
2. Insert Safe: Carefully slide the safe into the prepared cavity.
3. Secure Anchoring: Using the provided mounting hardware, securely anchor the safe to the structural elements of the wall. Ensure all anchor points are tight and the safe is firmly fixed.
4. Finish Wall: Once the safe is securely mounted, finish the surrounding wall area to conceal the installation and integrate the safe seamlessly.

5. Operating Instructions

This section details how to power your safe, set your personal code, and operate the locking mechanism.

5.1. Battery Installation

The safe requires 1.5V alkaline batteries (not included). The battery compartment is typically located on the inside of the safe door. Open the safe (if it's not already open from factory), locate the battery compartment, insert the batteries according to the polarity indicators, and close the compartment.

5.2. Setting Your Personal Code

Upon first use, or after replacing batteries, you will need to set your personal access code. Refer to the keypad image below for button identification.

Image 5.1: Close-up view of the CISA DGT Vision electronic keypad, featuring a numerical layout and function buttons.

1. With the safe door open, locate the internal programming button (often a small red or green button, or a switch). Press it once.
2. On the external keypad, enter your desired personal code (typically 3-8 digits).
3. Confirm the code by pressing the 'C' or 'Enter' button (refer to your specific model's instructions for exact confirmation key).
4. Test the new code with the door open first to ensure it works correctly before closing the safe.

5.3. Opening the Safe

1. Enter your personal code on the electronic keypad.
2. If the code is correct, the keypad will indicate successful entry (e.g., a green light or beep).
3. Within a few seconds, turn the handle (if present) or pull the door open.

5.4. Closing and Locking the Safe

1. Close the safe door firmly.
2. Turn the handle (if present) to engage the locking bolts. The safe will automatically lock.

5.5. Internal Light

The safe is equipped with an internal light feature to illuminate the contents when the door is open. This light typically activates automatically when the door is opened.

5.6. Removable Shelf

The safe includes a removable internal shelf, allowing you to customize the storage space according to your needs.

6. Maintenance

Regular maintenance ensures the longevity and reliable operation of your safe.

• Battery Replacement: Replace all batteries annually, or immediately if the low battery indicator activates (usually a specific light or sound from the keypad). Always use new 1.5V alkaline batteries.
• Cleaning: Clean the exterior of the safe with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the finish or electronic components.
• Locking Mechanism: Periodically check the locking bolts and door hinges for any obstructions or signs of wear. Do not lubricate the electronic lock mechanism.

7. Troubleshooting

If you encounter issues with your safe, refer to the following common problems and solutions:

• Safe Does Not Open with Code:
  • Ensure batteries are fresh and correctly installed.
  • Re-enter the code carefully.
  • If batteries are completely dead, some models offer an external power connector to temporarily power the keypad for opening. Consult manufacturer for details.
• Keypad Not Responding:
  • Check battery power. Replace batteries if necessary.
  • Ensure no debris is obstructing the buttons.
• Door Does Not Close/Lock Properly:
  • Ensure no items inside the safe are obstructing the door or locking bolts.
  • Check for any physical damage to the door or frame.
• Forgotten Code:
  • If you have forgotten your code, you may need to reset the safe. This often involves using an emergency override key (if provided) or following a specific reset procedure that may require opening the safe. Refer to the manufacturer's specific instructions for code reset.

8. Specifications

9. Warranty and Support

Specific warranty information for the CISA DGT Vision Electronic Wall Safe Model 182710300 is not provided in this document. For details regarding warranty coverage, terms, and conditions, please refer to the documentation included with your purchase or contact CISA customer support directly.

For technical assistance, spare parts, or service inquiries, please contact the manufacturer or your authorized dealer. Always provide your product model number (182710300) when seeking support.