1. Introduction
This manual provides essential instructions for the proper installation, operation, and maintenance of your PROFLO Amador PF9312 Toilet Tank. Please read this manual thoroughly before beginning installation or use to ensure safe and efficient performance. This product is a toilet tank only and requires a coordinating toilet bowl for complete installation.
Image 1.1: The PROFLO Amador PF9312 Toilet Tank. This image displays the white vitreous china toilet tank with its flush lever on the side.
2. Safety Information
Observe all local plumbing and building codes during installation. Always wear appropriate personal protective equipment, such as safety glasses and gloves, when handling plumbing fixtures and tools. Ensure the water supply is turned off before beginning any installation or maintenance work. If you are unsure about any part of the installation process, consult a qualified plumber.
3. Package Contents
Verify that all components are present and undamaged before proceeding with installation.
- PROFLO Amador PF9312 Toilet Tank (Vitreous China, White)
- Internal tank components (flush valve, fill valve, flush lever)
- Tank-to-bowl bolts and gasket (typically included with tank)
Note: A toilet bowl, toilet seat, and wax ring/flange bolts are sold separately and are required for a complete toilet installation.
4. Setup and Installation
4.1 Preparation
- Turn off the water supply to the toilet area.
- Remove any existing toilet tank and clean the area around the toilet bowl's mounting surface.
- Ensure the rough-in dimension (distance from the wall to the center of the drain pipe) is 12 inches for proper fitment.
4.2 Tank Installation
- Place the tank-to-bowl gasket onto the flush valve opening at the bottom of the toilet tank.
- Carefully align the tank with the bolt holes on the toilet bowl.
- Insert the tank-to-bowl bolts through the tank and bowl holes. Secure with washers and nuts from underneath the bowl, tightening evenly until the tank is stable and does not rock. Avoid overtightening to prevent cracking the vitreous china.
- Connect the water supply line to the fill valve shank at the bottom of the tank. Hand-tighten, then use a wrench for a final quarter-turn.
- Turn on the water supply slowly and check for leaks. Allow the tank to fill.
Image 4.1: The PROFLO Amador PF9312 Toilet Tank shown installed on a compatible toilet bowl. Note that the bowl and seat are separate components.
5. Operating Instructions
To operate the toilet, simply press down on the flush lever located on the side of the tank. This action lifts the flush valve, allowing water to flow from the tank into the toilet bowl, initiating the flush cycle. Release the lever once the flush is complete. The tank will then refill automatically.
6. Maintenance
6.1 Cleaning
Clean the exterior of the toilet tank with a soft cloth and mild, non-abrasive cleaning agents. Avoid harsh chemicals or abrasive scrubbers, as these can damage the vitreous china finish. For internal components, periodic inspection for mineral buildup is recommended. Use a toilet bowl cleaner specifically designed for internal tank use if necessary, following the product's instructions.
6.2 Component Inspection
Periodically inspect the fill valve, flush valve, and flush lever for proper function and wear. Ensure the flapper or seal is seating correctly to prevent leaks. Adjust the water level if needed, typically by adjusting the fill valve float mechanism according to the manufacturer's instructions for the specific fill valve model.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Tank does not fill or fills slowly | Water supply turned off; clogged fill valve; kinked supply line. | Ensure water supply is on; clean or replace fill valve; straighten supply line. |
| Tank continuously runs or leaks | Flapper not sealing properly; fill valve not shutting off; water level too high. | Inspect/replace flapper; adjust or replace fill valve; adjust water level. |
| Weak flush | Low water level in tank; clogged siphon jet or rim holes in bowl (bowl issue). | Adjust water level to correct height; clean bowl's siphon jet and rim holes (refer to bowl manual). |
For issues not listed here or if troubleshooting steps do not resolve the problem, contact PROFLO customer support or a qualified plumber.
8. Specifications
- Model: PF9312
- Material: Vitreous China
- Color: White
- Item Weight: 31.8 pounds
- Product Dimensions: 16.6 x 9.6 x 14.75 inches (Length x Width x Height)
- Installation Method: Floor Mounted (tank to bowl)
- Rough-In Dimension: 12 inches
- Included Components: Toilet Tank Only
9. Warranty and Support
PROFLO products are factory tested to ensure flawless function. This PROFLO toilet tank is covered under PROFLO's Fixtures warranty for one year after installation. For specific warranty details, claims, or technical support, please refer to the official PROFLO website or contact their customer service department. Keep your purchase receipt as proof of purchase for warranty purposes.
PROFLO Customer Support: Please visit www.proflo.com for contact information and further assistance.
