Flash Furniture Jude Tempered Glass Computer Desk with Pull-Out Keyboard Tray

Introduction

This manual provides detailed instructions for the assembly, operation, maintenance, and troubleshooting of your Flash Furniture Jude Tempered Glass Computer Desk with Pull-Out Keyboard Tray. Please read all instructions carefully before beginning assembly and retain this manual for future reference.

The Jude computer desk is designed to offer a functional and aesthetically pleasing workspace. It features a clear tempered glass surface, a space-saving sliding keyboard tray, and a sturdy frame with crisscross cherry-finished legs. This desk is suitable for various environments, including home offices, dorm rooms, and study areas.

Safety Information

• Ensure all parts are present and undamaged before assembly. Do not use if any parts are missing or broken.
• Assembly requires at least two people for safety and ease of installation.
• Do not overtighten screws during assembly, as this may damage the components. Tighten all fasteners securely once assembly is complete.
• The desk has a static weight capacity of 110 lbs. Do not exceed this limit.
• Keep small parts away from children during assembly to prevent choking hazards.
• Place the desk on a level surface to prevent instability.

Setup and Assembly

Assembly is required for this product. It is recommended that two people perform the assembly to ensure safety and efficiency. An Allen wrench is the primary tool required for assembly.

General Assembly Tips:

• Leave all bolts and screws slightly loose until the entire desk is assembled. This allows for minor adjustments to align holes properly. Once all components are in place, go back and tighten all fasteners securely.
• When attaching the keyboard glides to their brackets, these screws may be difficult to start. Apply firm, steady pressure with the correct size screwdriver. Mount the glides as far forward on the bracket as the holes allow.
• For the round tubes of the frame, note that most have a concave or 'dented' hole on one side. This is the side where screws should be inserted to ensure they are long enough to engage properly.
• When mounting the glass top, the screws are designed to be just long enough. They have a blunt tip, which can make it difficult to penetrate the cork pads on the aluminum mounts. Use the Allen wrench to create a pilot hole through the cork into the cavity before inserting the screw. It may be easier to place the glass top upside down on the floor and then position the frame on top to align the holes.

Image: The Flash Furniture Jude Computer Desk, showcasing its clear tempered glass top and cherry-finished crisscross legs.

Image: A detailed view of the crisscross cherry-finished legs, highlighting the design and construction.

Operating Instructions

Using the Pull-Out Keyboard Tray:

The desk includes a smooth-gliding pull-out keyboard tray designed to maximize your desktop space. To use, gently pull the tray forward until it reaches its full extension. To retract, push the tray back into its stored position under the main desk surface.

If you find the keyboard tray does not extend far enough for your comfort, you may consider adjusting its mounting position. Some users have found success by drilling new pilot holes on the bottom of the keyboard drawer, approximately 1 1/4 inches closer to the back of the drawer, to allow for greater extension.

Image: A close-up view of the pull-out keyboard tray, showing its functionality and design.

Image: The desk in use, demonstrating the ample work surface provided by the tempered glass top and the convenience of the sliding keyboard tray.

Maintenance

Cleaning the Desk:

• For the tempered glass surface, use a water-based cleaner and a soft cloth or paper towel. Avoid abrasive cleaners or harsh chemicals that could scratch or damage the glass.
• For the powder-coated frame and cherry-finished legs, wipe with a damp cloth and mild soap if necessary. Dry immediately to prevent water spots or damage.
• Regularly check all fasteners to ensure they remain tight. Retighten as needed to maintain the desk's stability.
• The desk is equipped with floor glides to protect your flooring. Ensure these glides are clean and intact to prevent scratching when moving the desk.

Troubleshooting

Common Issues and Solutions:

• Difficulty with Screw Alignment: If screw holes do not align perfectly during assembly, loosen all previously tightened screws slightly. This provides 'jiggle room' to maneuver components into place. Once aligned, tighten all screws progressively.
• Keyboard Tray Not Extending Sufficiently: If the keyboard tray feels too shallow or does not extend enough, consider adjusting its mounting. Some users have successfully re-drilled pilot holes for the keyboard drawer approximately 1 1/4 inches further back to allow for more forward extension.
• Glass Top Screws Difficult to Install: The screws for the glass top are designed to fit precisely. If you encounter difficulty, use the Allen wrench to create a small pilot hole through the cork pad on the aluminum mount before attempting to insert the screw. Placing the glass upside down on the floor and then positioning the frame on it can also aid in alignment.
• Desk Instability/Wobbling: Ensure all assembly screws are fully tightened. Check that the desk is placed on a flat, even surface. If the floor is uneven, use shims under the floor glides to stabilize the desk.

Specifications

Image: Visual representation of the desk dimensions: 35.5" W x 23.75" D x 29.75" H.

Warranty Information

This Flash Furniture Jude Tempered Glass Computer Desk comes with a 1-year limited warranty. This warranty covers manufacturing defects in materials and workmanship under normal use. Please retain your proof of purchase for any warranty claims.

For specific details regarding warranty coverage and limitations, please refer to the warranty card included with your product packaging or contact customer support.

Customer Support

If you have any questions, require assistance with assembly, or need to report a missing or damaged part, please contact Flash Furniture customer support. Our team is available to help you with any concerns regarding your product.

• Online Support: Visit the official Flash Furniture website for FAQs and support resources.
• Contact Information: Refer to your product packaging or the Flash Furniture website for the most current contact details, including phone numbers and email addresses.