Introduction
This manual provides essential information for the safe and effective use of your SYLVANIA 21367 F8T5/WW 8 Watt T5 Linear Fluorescent Tube. Please read these instructions carefully before installation and retain them for future reference. This product is designed for indoor use in compatible fixtures.
Safety Information
- Electrical Safety: Always disconnect power to the fixture at the circuit breaker or fuse box before installing, removing, or servicing the fluorescent tube. Failure to do so may result in electric shock or injury.
- Proper Handling: Fluorescent tubes contain a small amount of mercury. Handle with care to avoid breakage. If a tube breaks, ventilate the area and follow local guidelines for cleanup and disposal. Avoid direct contact with broken glass.
- Fixture Compatibility: Ensure the fixture is designed for T5 fluorescent tubes and has a G5 base. Using an incompatible fixture can lead to improper operation or damage.
- Operating Environment: This tube is intended for indoor use. Do not expose to water or excessive humidity.
- Disposal: Dispose of used fluorescent tubes according to local regulations, as they contain mercury. Many communities have recycling programs for fluorescent lighting.
Product Overview
The SYLVANIA 21367 F8T5/WW is an 8-watt T5 linear fluorescent tube designed to provide warm white light at a color temperature of 3000 Kelvin. It features a G5 miniature bi-pin base and is energy-efficient, suitable for various indoor lighting applications.
An image showing the SYLVANIA F8T5/WW 8 Watt T5 Linear Fluorescent Tube. The tube is cylindrical and clear, with a metallic base featuring two pins for electrical connection.
Setup and Installation
- Power Off: Before beginning installation, ensure the power supply to the lighting fixture is completely turned off at the circuit breaker or fuse box. Verify that the fixture is de-energized.
- Remove Old Tube (if applicable): If replacing an existing tube, carefully twist the old tube approximately 90 degrees and gently pull it out of the fixture's lampholders.
- Inspect Fixture: Check the fixture's lampholders for any damage or corrosion. Ensure they are clean and in good working condition.
- Insert New Tube: Align the two pins on each end of the SYLVANIA F8T5/WW tube with the slots in the fixture's lampholders. Gently push the tube into the lampholders until the pins are fully seated.
- Secure Tube: Once the pins are seated, rotate the tube approximately 90 degrees until it locks securely into place. Do not force the tube.
- Restore Power: Once the tube is securely installed, restore power to the fixture at the circuit breaker or fuse box.
- Test: Turn on the light switch to confirm proper operation of the new fluorescent tube.
Operating Instructions
The SYLVANIA 21367 F8T5/WW fluorescent tube operates by simply turning on the power switch connected to its fixture. It will provide immediate illumination. No special operating procedures are required beyond standard light switch operation.
Maintenance
- Cleaning: To clean the fluorescent tube, ensure the power is off and the tube is cool. Gently wipe the tube with a soft, dry, lint-free cloth. Do not use liquid cleaners or abrasive materials, as these can damage the tube's coating.
- Replacement: Replace the tube when it reaches the end of its life, indicated by flickering, dimming, or failure to light. Follow the installation steps in reverse to remove the old tube and then install a new one.
- Disposal: Due to the mercury content, proper disposal of used fluorescent tubes is crucial. Do not dispose of them in regular household trash. Contact your local waste management facility or recycling center for information on fluorescent lamp recycling programs in your area.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Tube does not light | No power to fixture; Tube not seated correctly; Defective tube; Defective ballast/fixture. | Check circuit breaker/fuse. Ensure tube is fully inserted and twisted into lampholders. Replace tube with a known good one. Consult an electrician for fixture/ballast issues. |
| Tube flickers | Loose connection; Tube nearing end of life; Cold temperature; Incompatible ballast. | Ensure tube is securely seated. Replace tube. Allow tube to warm up in cold environments. Verify ballast compatibility with T5 8W tubes. |
| Tube is dim | Tube nearing end of life; Dirty tube. | Replace tube. Clean tube surface as per maintenance instructions. |
Specifications
| Feature | Detail |
|---|---|
| Brand | SYLVANIA |
| Model Number | 21367 |
| Light Type | Fluorescent |
| Wattage | 8 watts |
| Bulb Shape Size | T5 |
| Bulb Base | G5 |
| Color Temperature | 3000 Kelvin (Warm White) |
| Color Rendering Index (CRI) | 95 |
| Voltage | 120 Volts (fixture dependent) |
| Indoor/Outdoor Usage | Indoor |
| Product Dimensions | 12 x 1.5 x 1 inches (approximate) |
| Item Weight | 0.16 ounces (approximate) |
| Special Feature | Energy Efficient |
Warranty Information
Specific warranty details for the SYLVANIA 21367 F8T5/WW 8 Watt T5 Linear Fluorescent Tube are not provided in this manual. For warranty inquiries, please refer to the product packaging or visit the official SYLVANIA website for the most current information.
Support
For further assistance or technical support regarding your SYLVANIA fluorescent tube, please visit the official SYLVANIA website or contact their customer service department. Contact information can typically be found on the brand's official website or product packaging.
