Fenton WPP16 6.5-inch Woofer Instruction Manual

1. Introduction

Thank you for choosing the Fenton WPP16 6.5-inch Woofer. This manual provides essential information for the proper installation, operation, and maintenance of your new audio component. Please read these instructions carefully before use to ensure optimal performance and longevity of the product.

The Fenton WPP16 is a high-quality 6.5-inch (16cm) woofer designed for excellent bass reproduction. It is suitable for various applications, including HiFi speaker systems, car audio installations, or as a replacement driver for existing enclosures.

Image 1: Front view of the Fenton WPP16 6.5-inch Woofer, showcasing its polypropylene cone and rubber surround.

2. Safety Instructions

• Electrical Safety: Always disconnect power from any amplifier or audio system before installing or servicing the woofer. Improper wiring can cause damage to the woofer, amplifier, or pose an electrical hazard.
• Handling: Handle the woofer carefully. Avoid touching the cone or surround with sharp objects. Do not drop the woofer.
• Impedance Matching: Ensure the woofer's impedance (8 Ohms) is compatible with your amplifier's output specifications. Mismatched impedance can lead to amplifier overheating or damage.
• Ventilation: Ensure adequate ventilation around the woofer and its enclosure to prevent overheating, especially during prolonged high-power operation.
• Volume Levels: Avoid operating the woofer at excessively high volume levels for extended periods, as this can cause permanent damage to the speaker.

3. Package Contents

• One (1) Fenton WPP16 6.5-inch Woofer

4. Product Features

The Fenton WPP16 woofer is engineered with the following key features:

• Polypropylene Cone: Provides excellent rigidity and damping for accurate bass reproduction.
• Rubber Suspension: Durable and flexible, allowing for extended cone excursion and improved low-frequency response.
• High Power Handling: Capable of handling up to 175 Watts maximum power (85 Watts RMS).
• Standard Impedance: 8 Ohms, compatible with a wide range of audio amplifiers.
• Wide Frequency Range: Designed to reproduce frequencies from 35 Hz to 8 kHz.
• Robust Construction: Features a heat-resistant voice coil and a substantial 850g (30 oz) magnet for reliable performance.

Image 2: The Fenton WPP16 Woofer highlighting its 6.5-inch polypropylene cone, 175W power handling, and 8 Ohm impedance.

5. Setup and Installation

Proper installation is crucial for the performance and safety of your woofer. Follow these steps carefully:

5.1 Mounting

1. Choose an Enclosure: The WPP16 is designed for use in a suitable speaker enclosure (e.g., sealed, ported, or bandpass). The enclosure's volume and tuning will significantly impact the woofer's performance. Consult speaker design resources for optimal enclosure parameters.
2. Prepare the Mounting Hole: Cut a circular hole in your enclosure with a diameter of 145 mm (5.7 inches). Ensure the mounting surface is flat and rigid.
3. Check Dimensions: Verify that the woofer's overall diameter (165 mm) and mounting depth (78 mm) fit your chosen location.
4. Secure the Woofer: Place the woofer into the mounting hole. Align the mounting holes on the woofer frame with the pre-drilled holes in your enclosure. Use appropriate screws (not included) to secure the woofer firmly, ensuring an airtight seal. Do not overtighten.

Image 3: Diagram illustrating the dimensions of the Fenton WPP16 Woofer, including overall diameter, mounting depth, and cutout diameter.

5.2 Wiring

1. Identify Terminals: The woofer has two terminals on the back. Typically, the wider terminal is positive (+) and the narrower one is negative (-). Refer to any markings on the woofer itself for confirmation.
2. Connect Speaker Wire: Use high-quality speaker wire of appropriate gauge for your power levels and cable length. Connect the positive (+) terminal of the woofer to the positive (+) output of your amplifier. Connect the negative (-) terminal of the woofer to the negative (-) output of your amplifier.
3. Ensure Polarity: Maintaining correct polarity across all speakers in your system is essential for proper sound reproduction and phase alignment.
4. Secure Connections: Ensure all connections are tight and free from short circuits.

Image 4: Back view of the Fenton WPP16 Woofer, showing the speaker terminals for wiring connections.

6. Operating the Woofer

Once installed and wired correctly, the Fenton WPP16 woofer operates as part of your audio system. Ensure your amplifier is powered on and set to a low volume level before playing audio. Gradually increase the volume to your desired listening level. For optimal performance, consider using a crossover network to direct only low frequencies to the woofer, preventing it from attempting to reproduce frequencies outside its intended range.

7. Maintenance

• Cleaning: Use a soft, dry cloth to gently wipe dust from the cone and frame. Avoid using harsh chemicals or abrasive materials.
• Inspection: Periodically inspect the woofer's cone, surround, and dust cap for any signs of damage or wear.
• Environment: Keep the woofer away from direct sunlight, extreme temperatures, and excessive moisture.

8. Troubleshooting

If you encounter issues with your Fenton WPP16 woofer, refer to the following common problems and solutions:

9. Specifications

Detailed technical specifications for the Fenton WPP16 6.5-inch Woofer:

Image 5: SPL vs Frequency Response graph, illustrating the acoustic performance characteristics of the Fenton WPP16 Woofer.

10. Warranty and Support

The Fenton WPP16 Woofer comes with a limited warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or contact your retailer. For technical support or further assistance, please reach out to the Fenton customer service department or your authorized dealer.