Satco S8115
Satco S8115 T5 Fluorescent Lamp User Manual
Model: S8115 | Brand: Satco
Introduction
Welcome to the user manual for the Satco S8115 T5 Fluorescent Lamp. This manual provides essential information for the safe and effective use, installation, and maintenance of your new fluorescent lamp. Please read this manual thoroughly before installation and retain it for future reference.
Product Overview
The Satco S8115 is a high-performance T5 fluorescent lamp designed for efficient lighting in various applications.
Key Features:
- 28 watts power consumption
- T5 form factor
- 6500K Daylight color temperature
- 85 Color Rendering Index (CRI)
- Miniature Bi Pin base
- Length: 45.81 inches, Width: 0.63 inches
Image: The Satco S8115 T5 Fluorescent Lamp, a long, slender tube with bi-pin connectors at one end.
Image: A collage showcasing various lighting applications and fixtures from Satco Nuvo, including chandeliers, kitchen lighting, bathroom vanity lights, and outdoor string lights.
Setup and Installation
Before installation, ensure the power supply to the fixture is turned off at the circuit breaker.
Installation Steps:
- Safety First: Always disconnect power to the fixture at the circuit breaker before handling electrical components.
- Inspect Fixture: Ensure your lighting fixture is compatible with T5 fluorescent lamps and has a miniature bi-pin base.
- Handle with Care: Hold the lamp by its ends to avoid touching the glass, which can leave oils and reduce lamp life.
- Align Pins: Carefully align the two pins on each end of the lamp with the corresponding slots in the fixture's lamp holders.
- Insert Lamp: Gently push the lamp into the lamp holders until it clicks securely into place. Do not force the lamp.
- Restore Power: Once the lamp is securely installed, restore power to the fixture.
- Test Operation: Turn on the light switch to confirm the lamp is functioning correctly.
Image: Close-up of outdoor string lights with exposed Edison-style bulbs, demonstrating a potential application for lighting products.
Operating Instructions
The Satco S8115 T5 Fluorescent Lamp operates immediately upon receiving power from a compatible fixture.
General Operation:
- Switching On/Off: Use the wall switch or fixture control to turn the lamp on or off.
- Warm-up Time: Fluorescent lamps may require a brief warm-up period to reach full brightness, especially in colder environments.
- Optimal Performance: For optimal lamp life and performance, avoid frequent on/off cycling.
Image: A modern living room with blue walls and stylish light fixtures, including wall sconces and a pendant light, illustrating interior lighting design.
Maintenance
Regular maintenance ensures the longevity and efficiency of your Satco S8115 T5 Fluorescent Lamp.
Cleaning:
- Disconnect Power: Always turn off and disconnect power to the fixture before cleaning.
- Cool Down: Allow the lamp to cool completely before handling.
- Wipe Clean: Gently wipe the lamp with a soft, dry, lint-free cloth. Do not use liquid cleaners or abrasive materials, as they can damage the lamp.
Replacement:
- End of Life: When the lamp reaches the end of its useful life (indicated by flickering, dimming, or failure to light), replace it with a new Satco S8115 or an equivalent T5 fluorescent lamp.
- Disposal: Dispose of old fluorescent lamps according to local regulations, as they contain small amounts of mercury. Many recycling centers accept fluorescent lamps.
Image: A classic black outdoor post light with a clear glass globe, positioned in front of a white picket fence, showcasing exterior lighting.
Troubleshooting
If your Satco S8115 T5 Fluorescent Lamp is not functioning as expected, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not light | No power to fixture | Check circuit breaker and wall switch. |
| Lamp does not light | Lamp not properly seated | Ensure lamp pins are fully inserted into lamp holders. |
| Lamp does not light | Defective lamp | Replace lamp with a new one. |
| Lamp does not light | Defective ballast or fixture wiring | Consult a qualified electrician. |
| Lamp flickers or dims | Lamp nearing end of life | Replace lamp. |
| Lamp flickers or dims | Incorrect lamp type for ballast | Ensure lamp is compatible with fixture's ballast. |
| Lamp flickers or dims | Loose connection | Ensure lamp is securely seated. |
Image: A smartphone displaying a smart lighting control app, with a house in the background illuminated by various colored lights, suggesting advanced lighting solutions.
Specifications
| Attribute | Value |
|---|---|
| Model | S8115 |
| Brand | Satco |
| Light Type | Fluorescent |
| Wattage | 28 watts |
| Color Temperature | 6500 Kelvin (Daylight White) |
| Color Rendering Index (CRI) | 85 |
| Base Type | Miniature Bi Pin |
| Shape | T5 |
| Item Length | 45.81 inches |
| Item Width | 0.63 inches |
| Material | Glass |
| Item Weight | 1.65 pounds |
| UPC | 045923081156 |
Warranty Information
The Satco S8115 T5 Fluorescent Lamp comes with an average rated hour limited warranty. For specific details regarding warranty coverage and claims, please refer to the product packaging or contact Satco customer support.
Customer Support
For further assistance, technical support, or inquiries regarding your Satco S8115 T5 Fluorescent Lamp, please contact Satco customer service.
- Online Support: Visit the official Satco website for FAQs and support resources.
- Brand Store: Explore other Satco products and information at the Satco Store on Amazon.
Image: The Satco Nuvo brand logo, featuring stylized text.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.