Important Safety Information
Please read and understand all instructions before beginning installation. Failure to do so may result in electric shock, fire, or other injuries which can be fatal or cause permanent damage. Keep these instructions for future reference.
- Always disconnect power at the main circuit breaker before installation or servicing.
- This fixture is intended for outdoor use in damp locations (covered porches or patios).
- All wiring must be in accordance with national and local electrical codes. If you are unsure about wiring, consult a qualified electrician.
- Ensure all connections are secure and properly insulated.
- Do not exceed the maximum wattage specified for the light bulbs.
- Handle glass components with care to prevent breakage.
- This product may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Wash hands after handling.
Package Contents
Verify that all components are present before beginning installation:
- 1 x John Timberland Casa Marseille Outdoor Hanging Light Fixture
- 1 x Canopy (6" diameter x 1 1/4" high)
- 1 x Chain (5-feet)
- Mounting Hardware (screws, wire nuts, etc. - typical for light fixtures)
- Instruction Manual
Image: Complete light fixture with chain and canopy.
Specifications
| Feature | Detail |
|---|---|
| Brand | John Timberland |
| Model Number | U4082 (Manufacturer Part Number: 10-3405-LP113-B2-XL) |
| Dimensions (H x W) | 30" high x 16 3/4" wide |
| Canopy Dimensions | 6" diameter x 1 1/4" high |
| Weight | 6.47 lbs (Product weight), 18.96 lbs (Shipping weight) |
| Chain Length | 5-feet (included) |
| Finish | Veranda Bronze |
| Glass Type | Champagne Hammered Glass |
| Bulb Base | E12 Candelabra Base |
| Number of Lights | 4 |
| Max Wattage per Bulb | 40 Watts (160 Watts total) |
| Voltage | 120 Volts |
| Indoor/Outdoor Usage | Outdoor (Damp Location Rated) |
| Sloped Ceiling Adaptable | Yes |
| Required Assembly | No (Fixture is pre-assembled, installation required) |
Image: Product dimensions showing 30 inches high and 16.75 inches wide.
Installation Instructions
1. Pre-Installation
- Turn off Power: Before starting, ensure the power to the circuit is turned off at the main fuse box or circuit breaker.
- Prepare Area: Clear the installation area. Ensure you have all necessary tools (screwdriver, wire strippers, electrical tape, etc.) and the included hardware.
- Review Local Codes: Consult local electrical codes for specific requirements in your area.
2. Mounting the Fixture
- Attach the mounting bracket (not explicitly listed but standard) to the junction box in the ceiling using the provided screws.
- Determine the desired hanging height. The fixture includes 5 feet of chain. Adjust the chain length by removing links as needed.
- Thread the electrical wires through the chain and the canopy.
- Secure the chain to the mounting bracket and the top loop of the fixture.
3. Wiring
- Connect the fixture's ground wire (usually bare copper or green) to the house ground wire (usually bare copper or green) using a wire nut.
- Connect the fixture's neutral wire (usually white) to the house neutral wire (usually white) using a wire nut.
- Connect the fixture's hot wire (usually black) to the house hot wire (usually black) using a wire nut.
- Carefully tuck all wires into the junction box.
4. Final Assembly
- Slide the canopy up against the ceiling, covering the junction box and mounting bracket.
- Secure the canopy in place with the provided screws or decorative nuts.
- Install four (4) E12 candelabra base bulbs (not included) into the sockets. Do not exceed 40 watts per bulb.
- Restore power at the main circuit breaker and test the light fixture.
Image: The Casa Marseille light fixture installed on a covered porch.
Operating Instructions
Bulb Requirements
This fixture requires four (4) E12 candelabra base light bulbs. The maximum wattage for each bulb is 40 watts. Compatible bulb types include incandescent, fluorescent, and LED. For best aesthetic results, clear glass Edison filament bulbs are recommended (as shown in product images).
Power Control
The light fixture is controlled by a standard wall switch (not included) connected to the electrical circuit. It does not feature integrated motion sensors or dusk-to-dawn functionality.
Image: Detail of the champagne hammered glass and internal bulb sockets.
Maintenance
- Cleaning: To clean the fixture, turn off the power and wipe with a soft, damp cloth. Do not use abrasive cleaners or solvents as they may damage the finish or glass.
- Bulb Replacement: Ensure power is off before replacing bulbs. Allow bulbs to cool completely before touching. Unscrew old bulbs and screw in new E12 candelabra base bulbs (max 40W each).
- Inspection: Periodically inspect the fixture for any signs of wear, loose connections, or damage. Address any issues promptly.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on | 1. Power is off. 2. Loose wiring connection. 3. Faulty bulb. 4. Circuit breaker tripped. | 1. Ensure power is on at the switch and circuit breaker. 2. Check all wiring connections (with power off). 3. Replace bulb(s). 4. Reset the circuit breaker. |
| Bulbs burn out quickly | 1. Incorrect bulb wattage. 2. Loose connection. | 1. Ensure bulbs do not exceed 40 watts. 2. Check bulb connections and wiring (with power off). |
| Fixture hums or flickers | 1. Loose wiring. 2. Incompatible dimmer switch (if applicable). | 1. Check all wiring connections (with power off). 2. Ensure dimmer switch is compatible with bulb type. |
Warranty and Support
Warranty: This John Timberland product comes with a Limited 1-year warranty from the manufacturer.
Customer Support: For assistance with installation, troubleshooting, or warranty claims, please contact LAMPS PLUS customer support. Refer to your purchase documentation for specific contact details or visit the John Timberland Store on Amazon.