Detex V Series Exit Trim Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of the Detex V Series Grade 1 Exit Trim. This product is designed for use with Detex V40/V50 Series Exit Devices, featuring a Classroom function with an S Lever and a Sprayed Aluminum Finish. It is non-handed, allowing for versatile installation.

Please read all instructions carefully before beginning installation or operation to ensure proper function and safety.

2. Product Overview

Figure 2.1: Detex V Series Exit Trim, showing the S lever and the rectangular escutcheon plate in a sprayed aluminum finish. The trim is designed to integrate with Detex V40/V50 Series Exit Devices.

The Detex V Series Exit Trim is a robust component designed to provide secure and reliable access control for doors equipped with Detex V40/V50 Series Exit Devices. Its non-handed design simplifies installation, making it suitable for both left-hand and right-hand door applications. The classroom function allows the exterior lever to be locked or unlocked by key, while the interior always allows free egress.

3. Setup and Installation

Proper installation is crucial for the functionality and security of the exit trim. Refer to the specific installation instructions provided with your Detex V40/V50 Series Exit Device for complete details, as this trim is an accessory to that device.

3.1. Tools Required

• Screwdriver set (Phillips and Flathead)
• Measuring tape
• Drill (if new holes are required)
• Pencil or marker

3.2. Pre-Installation Checks

1. Verify that all components listed in the packaging are present.
2. Ensure the door preparation (bore holes, mortise) matches the requirements for the Detex V40/V50 Series Exit Device and this trim.
3. Confirm the handing of the door and the non-handed nature of the trim.

3.3. Installation Steps

1. Attach the exterior trim assembly to the door, aligning it with the prepared holes for the exit device.
2. Secure the trim using the provided fasteners, ensuring it is flush against the door surface. Do not overtighten.
3. Install the spindle or cam through the door and into the exit device mechanism, ensuring proper engagement with the lever.
4. Test the lever operation to confirm smooth movement and proper retraction of the latch bolt when the exit device is engaged.
5. If a cylinder is to be added (this model is less cylinder), ensure the cylinder preparation is correct and the cylinder operates the locking mechanism smoothly.

4. Operating Instructions

The Detex V Series Exit Trim with Classroom function provides controlled access from the exterior while maintaining free egress from the interior.

4.1. Exterior Operation (Classroom Function)

• To Unlock: Insert the correct key into the cylinder (if installed) and turn to retract the latch bolt. The exterior lever will then operate freely.
• To Lock: Insert the correct key into the cylinder (if installed) and turn to engage the locking mechanism. The exterior lever will become rigid and will not retract the latch bolt.
• When the exterior lever is locked, entry is restricted.

4.2. Interior Operation

• From the interior, the exit device always allows free egress. Pushing the push bar or operating the interior lever (if applicable to the exit device) will retract the latch bolt, allowing the door to open, regardless of the exterior lock status.

5. Maintenance

Regular maintenance ensures the longevity and reliable operation of your Detex V Series Exit Trim.

5.1. Cleaning

• Clean the exterior surface with a soft, damp cloth.
• Avoid abrasive cleaners, solvents, or harsh chemicals, as these can damage the sprayed aluminum finish.

5.2. Lubrication

• Periodically apply a small amount of silicone-based lubricant to the moving parts of the lever mechanism and the spindle.
• Do not lubricate the cylinder mechanism unless specifically recommended by a locksmith or the cylinder manufacturer.

5.3. Inspection

• Regularly inspect the trim for any signs of wear, damage, or loose fasteners.
• Ensure all screws are tight. If any are loose, gently tighten them.
• Check the lever for smooth operation and ensure it returns to its original position without sticking.

6. Troubleshooting

This section addresses common issues you might encounter with your Detex V Series Exit Trim.

If you encounter issues not listed here or if the suggested solutions do not resolve the problem, please contact Detex customer support or a qualified locksmith.

7. Specifications

• Model Number: 08BN 689
• Product Type: Exit Trim
• Series: V Series
• Grade: 1
• Function: Classroom (S Lever)
• Compatibility: Detex V40/V50 Series Exit Devices
• Cylinder: Less Cylinder (requires separate purchase and installation of compatible cylinder)
• Finish: Sprayed Aluminum
• Handing: Non-handed
• Material: Aluminum
• Package Dimensions: 6.63 x 4.63 x 1.13 inches
• Item Weight: 3.3 Pounds
• Manufacturer: Detex
• Date First Available: February 12, 2012

8. Warranty Information

Detex products are manufactured to high standards and are backed by a manufacturer's warranty. For specific warranty terms and conditions applicable to the Detex V Series Exit Trim, please refer to the warranty documentation included with your original Detex V40/V50 Series Exit Device or visit the official Detex website. Keep your proof of purchase for warranty claims.

9. Customer Support

For technical assistance, replacement parts, or further inquiries regarding your Detex V Series Exit Trim, please contact Detex customer support.

Detex Corporation
Contact information typically found on the manufacturer's official website or product packaging.

When contacting support, please have your product model number (08BN 689) and purchase date available.