1. Introduction
The Leviton SureSlide Dimmer Switch (Model R62-06674-P0W) is designed to provide smooth, full-range dimming for various bulb types, including dimmable LED, Halogen, and Incandescent bulbs. This device allows for precise control over lighting levels, enhancing comfort and energy efficiency in your home or office environment. It features a distinct ON/OFF switch that maintains your preferred light setting when the switch is toggled.
Figure 1.1: Front view of the Leviton SureSlide Dimmer Switch, showing the slide control and ON/OFF rocker switch.
2. Safety Information
WARNING: RISK OF ELECTRIC SHOCK. Improper installation or use of this product can result in serious injury or death. Always turn off power at the circuit breaker or fuse box before wiring. This device must be installed in accordance with all national and local electrical codes.
- Ensure power is disconnected at the circuit breaker before installation, servicing, or removing the fixture.
- Use only with copper or copper clad wire.
- This product is intended for indoor use only.
- If you are unsure about any part of these instructions, consult a qualified electrician.
- Proposition 65 Warning: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
3. Product Features
- Smooth Slide-Action Dimming: Provides precise control over light levels.
- Separate ON/OFF Switch: Preserves the set light level when the switch is turned off and back on.
- Broad Compatibility: Designed for use with dimmable LED, CFL, Halogen, and Incandescent bulbs.
- Slim Profile: Less than 1 inch depth for easier installation in most wallboxes.
- Versatile Installation: Supports both single-pole (one location) and 3-way (two locations) wiring configurations.
- Adjustable Dimming Range: Features an adjustable minimum and maximum dimming range for LED bulbs to optimize performance and prevent flicker.
- No Neutral Wire Required: Works with existing wiring, simplifying installation.
Figure 3.1: Key features of the SureSlide Dimmer, including the integrated slider, separate ON/OFF switch, and mode selector.
4. Setup and Installation
4.1 Before You Begin
- Turn OFF power at the circuit breaker or fuse box.
- Remove the existing wallplate and switch.
- Carefully identify the wiring in your wallbox.
4.2 Wiring Instructions
The SureSlide dimmer supports both single-pole and 3-way wiring configurations. No neutral wire is required for installation.
Figure 4.1: Rear view of the dimmer switch, highlighting its slim depth and wiring terminals for easier installation.
Figure 4.2: Illustration of single-pole wiring (controls lights from one location) and 3-way wiring (controls lights from two locations).
- Single-Pole Installation: Connect the dimmer to control lights from one location. Typically involves two wires from the light fixture and one ground wire.
- 3-Way Installation: Use the 6674 dimmer in the main location and pair it with a standard 3-way switch (sold separately) in a second location. This is suitable for rooms with multiple entrances or staircases.
For detailed wiring diagrams, please refer to the official Installation Manual (PDF).
4.3 Bulb Compatibility
The dimmer is compatible with 150W-120VAC dimmable LED/CFL and 600W-120VAC incandescent/halogen bulbs. For optimal performance with LED bulbs, it is recommended to consult Leviton's bulb compatibility tool on their official website.
Figure 4.3: The dimmer is tested for compatibility with a wide range of dimmable LED bulbs.
5. Operating Instructions
5.1 Basic Operation
- Turning ON/OFF: Use the rocker switch at the bottom of the dimmer to turn the lights on or off.
- Dimming: Use the vertical slide control to adjust the light level. Slide up for brighter light and down for dimmer light.
5.2 Adjusting Minimum Light Level (Programming Mode)
This feature allows you to set the lowest dimming level for your LED bulbs, which can help eliminate flicker and optimize performance at low light settings.
Figure 5.1: The mode selector switch, located behind the wallplate, allows adjustment of minimum and maximum light levels.
- Ensure the dimmer is set to the OFF position.
- Locate the bulb selector switch (often labeled "MODE" or similar) on the side of the dimmer, usually accessible by removing the wallplate. Set it to the LED/Incandescent position.
- Push the rocker switch to the ON position.
- Set the bulb selector switch to the CFL position.
- Raise or lower the slide control to achieve your desired minimum light level.
- Set the bulb selector switch back to the LED/Incandescent position.
- A momentary flash of the bulb will confirm the new setting.
- Push the rocker switch to the OFF position.
- For dimmable CFL lamps, you must return the bulb selector to the CFL position after setting the minimum level.
6. Maintenance
The Leviton SureSlide Dimmer Switch requires minimal maintenance. To clean the device, gently wipe the surface with a soft, damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or internal components. Ensure power is off before cleaning.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Lights flicker or buzz at low dimming levels. | Incompatible LED/CFL bulbs or minimum dimming level not set correctly. | Adjust the minimum light level using the programming mode (Section 5.2). Ensure your bulbs are listed as dimmable and compatible with the dimmer. Consult Leviton's bulb compatibility tool. |
| Lights do not turn on. | No power to the switch, incorrect wiring, or faulty bulb. | Check the circuit breaker. Verify wiring connections (Section 4.2). Test with a known working bulb. |
| Dimmer does not dim. | Bulbs are not dimmable, or incorrect wiring. | Ensure all connected bulbs are explicitly labeled as dimmable. Re-check wiring according to the installation manual. |
| Dimmer feels warm. | Normal operation. | It is normal for dimmers to feel warm during operation. If it becomes excessively hot or emits smoke/odor, immediately turn off power at the breaker and contact a qualified electrician. |
For more comprehensive troubleshooting, refer to the official Installation Manual (PDF).
8. Specifications
Figure 8.1: Product dimensions for the Leviton SureSlide Dimmer Switch.
| Specification | Value |
|---|---|
| Model Number | R62-06674-P0W |
| Operation Mode | ON-OFF |
| Current Rating | 1 Amps |
| Operating Voltage | 120 Volts |
| Wattage (Incandescent/Halogen) | 600W |
| Wattage (Dimmable LED/CFL) | 150W |
| Frequency | 60Hz |
| Circuit Type | Single-pole or 3-way |
| Color | White |
| Item Dimensions (L x W x H) | 2 x 2 x 4 inches |
| Item Weight | 3.2 ounces |
| Material | Aluminum (Contact Material) |
| Terminal Type | Screw |
9. Warranty Information
The Leviton SureSlide Dimmer Switch (Model R62-06674-P0W) is covered by a 5 Year Limited Warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. For full warranty terms and conditions, please refer to the documentation included with your product or visit the official Leviton website.
10. Support and Resources
For additional support, detailed installation guides, and product information, please utilize the following resources:
- Official Installation Manual (PDF): Download Here
- Leviton Official Website: Visit www.leviton.com for product registration, FAQs, and customer service contact information.
- Bulb Compatibility Tool: For best performance with LED bulbs, refer to Leviton's online bulb compatibility tool.
