1. Introduction
This manual provides detailed instructions for the installation of the Metra 99-7013TB Single DIN Dash Installation Kit. This kit is specifically designed to integrate an aftermarket single DIN radio into the dashboard of 2007-2010 Mitsubishi Outlander vehicles, ensuring a seamless and factory-like appearance. It includes a removable oversized storage pocket and all necessary hardware for installation.
2. Safety Information
Always prioritize safety during installation. Disconnect the vehicle's battery before beginning any electrical work. Wear appropriate personal protective equipment, such as safety glasses. If you are unsure about any step, consult a qualified automotive technician. Improper installation can lead to vehicle damage or personal injury.
3. Package Contents
Verify that all components are present before starting the installation:
- Metra 99-7013TB Dash Kit (Main Panel)
- Removable Oversized Storage Pocket
- Radio Support Brackets (integrated or separate)
- Necessary Installation Hardware (screws, clips, etc.)
Figure 1: Front view of the Metra 99-7013TB Single DIN Dash Installation Kit. This image displays the main panel with the opening for a single DIN radio and the integrated storage pocket area.
4. Setup and Installation
4.1 Tools Required (Not Included)
- Panel Removal Tool
- Screwdrivers (Phillips and Flathead)
- Socket Wrench Set
- Wire Strippers/Crimpers (if installing a new radio)
- Heat Gun and Thin Razor Blade (for sticker removal, if applicable)
4.2 Pre-Installation Steps
- Disconnect Battery: Before starting, disconnect the negative terminal of the vehicle's battery to prevent electrical shorts.
- Remove Factory Radio and Trim: Carefully remove the factory radio and surrounding dash trim panel. Refer to your vehicle's service manual for specific instructions on trim panel removal.
- Remove Hazard Button and Warning Stickers: The factory trim panel contains the hazard button assembly and potentially passenger airbag/seatbelt warning stickers. These must be carefully transferred to the new Metra dash kit.
- For the hazard button, carefully detach the circuit board from the old panel.
- For warning stickers, use a heat gun on a low setting to gently warm the adhesive. Then, use a thin razor blade to carefully lift a corner and slowly peel the sticker off. Avoid bending or creasing the stickers.
- Once removed, apply these components to the corresponding locations on the Metra 99-7013TB dash kit. For stickers, a small amount of super glue may be used if the original adhesive is no longer effective.
Figure 2: Rear view of the Metra 99-7013TB Dash Kit. This shows the mounting points and internal structure for securing the aftermarket radio and transferring vehicle components.
4.3 Kit Assembly and Radio Mounting
- Prepare the Dash Kit:
- If installing a single DIN radio, the removable oversized storage pocket will be used. Ensure it is securely fitted into the lower portion of the radio opening.
- If installing a double DIN radio (though this is a single DIN kit, some users modify it), the center bar and storage pocket would need to be carefully removed. This modification is not officially supported by the single DIN kit design.
- Mount the Aftermarket Radio: Attach the aftermarket single DIN radio to the Metra dash kit using the provided screws and integrated radio supports. Ensure the radio is flush and securely fastened.
- Connect Wiring: Connect the aftermarket radio's wiring harness to the vehicle's wiring harness. If a wiring adapter (e.g., Metra 70-7005) is used, connect it according to its instructions.
Figure 3: Angled front view of the Metra 99-7013TB Dash Kit, highlighting the textured matte black finish designed to match the factory dashboard.
4.4 Final Installation
- Test Connections: Before fully reassembling, reconnect the vehicle's battery and test the functionality of the new radio, hazard lights, and any transferred warning indicators.
- Install Dash Kit: Carefully align the Metra dash kit with the vehicle's dashboard opening. Press firmly to engage all clips and secure any screws that hold the trim in place. Ensure a gapless fit.
- Reconnect Battery: Once the installation is complete and verified, ensure the battery is securely reconnected.
Figure 4: Top view of the Metra 99-7013TB Dash Kit, showing the curvature and mounting tabs for integration into the vehicle's dashboard.
5. Operating the Dash Kit
The Metra 99-7013TB is an installation kit and does not have operational functions itself. Its purpose is to provide a secure and aesthetically pleasing housing for your aftermarket single DIN radio. The removable oversized storage pocket offers convenient storage space below the radio.
6. Maintenance
To maintain the appearance of your dash kit, clean it with a soft, damp cloth. Avoid using harsh chemicals or abrasive cleaners, as these can damage the finish. Regular cleaning will help preserve its factory-matched look.
7. Troubleshooting
- Poor Fitment: Ensure all factory clips and mounting points are correctly aligned with the dash kit. Double-check that no wires are obstructing the kit from seating properly.
- Radio Not Functioning: Verify all wiring connections, including power, ground, and accessory wires. Ensure the vehicle's battery is fully reconnected.
- Hazard Button or Warning Lights Not Working: Recheck the transfer of the hazard button circuit board and warning stickers. Ensure they are correctly positioned and making proper contact.
- Scratches or Damage During Installation: Exercise caution with panel removal tools. Minor imperfections can sometimes be buffed out with automotive interior detailing products.
8. Specifications
- Brand: Metra
- Model Number: 99-7013TB
- Material: Acrylonitrile Butadiene Styrene (ABS) Plastic
- Color: Black (Textured Matte Finish)
- Compatibility: 2007-2010 Mitsubishi Outlander Vehicles
- Radio Type: Single DIN (ISO mount)
- Dimensions (L x W x H): Approximately 15 x 12 x 3.25 inches
- Item Weight: Approximately 2.72 ounces
- Manufacturer: Metra Electronics Corp
- UPC: 161586909399, 132017803456, 086429247752, 163121233099
- GTIN: 00086429247752
9. Warranty and Support
Specific warranty details for the Metra 99-7013TB Dash Installation Kit are not provided in this document. For warranty information, technical support, or further assistance, please contact Metra Electronics Corp directly through their official website or customer service channels. Always retain your proof of purchase for warranty claims.
