Introduction
This manual provides essential information for the proper use and maintenance of your POOL BLASTER Genuine Microfilter Bags. These bags are engineered to be used in conjunction with reusable Pool Blaster filters for extra-fine cleaning, capturing sand, silt, and other fine debris to leave your pool or spa sparkling clean.
Image: POOL BLASTER Genuine Microfilter Bags 5-Pack, showing the product packaging and two individual microfilter bags.
Compatibility
The POOL BLASTER Genuine Microfilter Bags (part number P30X022MF) are compatible with the following Pool Blaster cordless pool cleaner models:
- Aqua Broom 10000AB
- Aqua Broom Ultra 10051AB
- Catfish 20000CL/20050CL
- Catfish Ultra 21001DL/21051DL
- Fusion PV-5 14151AL
- Hydro 100 14051AL
- iVac 250 IVAC250/25000GL/25050GL
- iVac C2 IVCF702
- Max 30000ML
- Max CG 32000KL
- Max HD 32000HL
- Millennium 33001HL
- Volt FX-4 24000GL/24050GL
- Volt FX-8 34000KL
Setup and Installation
These microfilter bags are designed to be used in conjunction with your existing reusable Pool Blaster filter bags. Follow these steps to properly install the microfilter bag into your compatible Pool Blaster cleaner:
- Ensure your Pool Blaster cleaner is turned off and disconnected from any power source.
- Open the debris chamber of your Pool Blaster cleaner and remove the existing filter bag.
- Carefully insert the microfilter bag into the reusable filter bag, ensuring it fits snugly. The microfilter bag acts as an additional layer of filtration.
- Place the combined filter bags back into the debris chamber of your Pool Blaster cleaner.
- Securely close the debris chamber.
Image: A four-step diagram illustrating how to install the microfilter bag into a Pool Blaster cleaner's existing filter system.
Video: Demonstrates the installation process of a multilayer filter bag into a Pool Blaster cleaner.
Operating Instructions
Once the microfilter bag is installed, operate your Pool Blaster cleaner as per its original instruction manual. The microfilter bag works in tandem with your cleaner's primary filter to capture finer particles such as sand, silt, and other small debris, providing a more thorough cleaning.
Video: Shows the POOL BLASTER Catfish Ultra (Gen 2) Cordless Pool Vacuum in operation, demonstrating how it cleans the pool floor and steps.
Maintenance
For optimal performance, it is recommended to dispose of the microfilter bags after each use, especially when cleaning ultra-fine dirt particles. High-density mesh can become blocked, affecting the vacuum's efficiency.
- After each cleaning session, remove the microfilter bag from the cleaner.
- Carefully empty any collected debris into a waste receptacle.
- As these are disposable microfilter bags, replace with a new bag for subsequent cleanings to ensure maximum filtration efficiency.
Specifications
| Feature | Detail |
|---|---|
| Product Dimensions (Packaging) | 0.5 x 4.5 x 8 inches |
| Product Dimensions (Bag) | 8"L x 0.41"W x 10"H |
| Item Weight | 1.6 ounces |
| Manufacturer | Water Tech Corp. |
| Item Model Number | P30X022MF |
| Material | Mesh |
| Reusability | Disposable |
Troubleshooting
If you experience reduced suction or cleaning performance with your Pool Blaster cleaner while using the microfilter bags, consider the following:
- Blocked Water Flow: The high-density mesh of the microfilter bags is designed to capture ultra-fine dirt particles. If the bag becomes heavily saturated with these particles, it can block water flow and reduce the vacuum's performance.
- Solution: Immediately replace the used microfilter bag with a new one. Regular replacement ensures consistent and effective cleaning.
Warranty and Support
For specific warranty information or technical support regarding your POOL BLASTER products, please refer to the documentation included with your Pool Blaster cleaner or visit the official Water Tech Corp. website. This product is a genuine replacement part manufactured by Water Tech Corp.
