Introduction
This manual provides detailed instructions for the safe and efficient operation of your Utilitech 15-Amp 1-Outlet Digital Residential Plug-in Countdown Function Lighting Timer. Please read this manual thoroughly before use and retain it for future reference.
Important Safety Information
- Indoor Use Only: This timer is designed for indoor use in dry locations. Do not expose to water or moisture.
- Electrical Rating: Do not exceed the maximum electrical rating of 15 Amps. Overloading may cause damage or fire.
- Polarized Outlet: Ensure the timer is plugged into a polarized outlet correctly.
- Children: Keep out of reach of children.
- Cleaning: Unplug before cleaning. Use a dry cloth only.
- Disassembly: Do not attempt to disassemble or repair the unit. Refer all servicing to qualified personnel.
Product Features
- Automatically turns devices on/off.
- Cycle repeats daily, 1 polarized outlet.
- Large LCD digital display.
- Easy to set: time, on, off.
- Mini type bar timer will not block other wall outlet.
Setup Guide
Unboxing and Initial Inspection
Carefully remove the timer from its packaging. Inspect the unit for any signs of damage. If damaged, do not use and contact customer support.
Figure 1: Front view of the Utilitech Digital Timer in its retail packaging. The timer features a digital display and control buttons for setting time and functions. The packaging highlights key features like "Easy-program" and "Slim design."
Figure 2: Back view of the Utilitech Digital Timer packaging. This side displays the two-prong plug, electrical ratings, and compliance information. It also includes the UPC: 686140684241.
Plugging In
- Locate a standard 120V AC wall outlet.
- Plug the Utilitech Digital Timer directly into the wall outlet. Ensure it is firmly seated.
- The LCD display should illuminate, indicating power.
Operating Instructions
Setting the Current Time
- Press the HOUR button to adjust the hour.
- Press the MIN button to adjust the minute.
- The time will automatically save after a few seconds of inactivity.
Programming On/Off Times
The timer allows for setting specific ON and OFF times for connected devices.
- Press the ON button to set the desired turn-on time. Use HOUR and MIN to adjust.
- Press the OFF button to set the desired turn-off time. Use HOUR and MIN to adjust.
- To activate the programmed schedule, ensure the timer is in "Auto" mode (if applicable, refer to display icons).
Using the Countdown Function
The countdown function allows the connected device to remain on for a set duration before turning off.
- Plug the device you wish to control into the timer's outlet.
- Press the COUNTDOWN button (if available, or cycle through modes until countdown is active).
- Use the HOUR and MIN buttons to set the desired countdown duration.
- The timer will automatically turn off the device once the countdown reaches zero.
Resetting the Timer
To clear all settings and return the timer to its default state:
- Locate the small RESET button (often recessed).
- Use a pointed object (e.g., a paperclip) to press and hold the RESET button for approximately 3 seconds until the display clears.
Maintenance
The Utilitech Digital Timer requires minimal maintenance.
- Cleaning: Unplug the timer from the wall outlet before cleaning. Wipe the exterior with a soft, dry cloth. Do not use liquid cleaners or abrasive materials.
- Storage: If storing the timer for an extended period, unplug it and keep it in a cool, dry place away from direct sunlight.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Timer display is blank. | No power to the outlet. | Check the wall outlet with another device. Check circuit breaker. |
| Device not turning on/off at programmed times. | Incorrect programming; Timer not in "Auto" mode; Device not properly plugged into timer. | Review programming steps. Ensure timer is in "Auto" mode. Confirm device is fully plugged into the timer. |
| Display shows erratic characters. | Temporary electrical interference. | Perform a full reset of the timer. |
Specifications
- Model Number: 00144506
- Brand: Utilitech
- Type: Digital Plug-in Timer
- Number of Outlets: 1
- Maximum Amperage: 15 Amp
- Voltage: 120V AC, 60Hz
- Material: Plastic
- Color: White
- Item Weight: 5 ounces
- Dimensions: 9.29 x 5.91 x 2.6 inches (Package)
- Certifications: CSA, ETL, UL
- UPC: 0686140684241
Warranty and Support
For information regarding warranty coverage or technical support, please refer to the original product packaging or contact Utilitech customer service directly. Contact details are typically provided on the manufacturer's website or included documentation.
