Derale 15708 Remote Filter Mount Kit Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the Derale 15708 Remote Filter Mount Kit. This kit is designed to relocate your engine's oil filter to a more accessible location, which can be beneficial for various applications, including those requiring custom engine configurations or easier maintenance access.

Safety Information

Always prioritize safety when working on your vehicle. Ensure the engine is cool before beginning any work. Wear appropriate personal protective equipment, including gloves and eye protection. Disconnect the vehicle's battery before installation. Consult a professional mechanic if you are unsure about any steps. Oil can be hot and cause burns. Use proper tools and techniques to avoid injury or damage to components.

Package Contents

Verify that all components are present before beginning installation:

• Remote Filter Mount Unit
• Mounting Hardware (screws)
• Hose Barbs (brass fittings)
• Threaded Nipple
• (Hoses and clamps are typically sold separately or may be included in specific kits. Refer to your packaging.)

Figure 1: Overview of the Derale 15708 Remote Filter Mount Kit components, including the main mount, brass hose barbs, and mounting screws.

Installation

1. Preparation: Ensure the engine is off and cool. Drain the engine oil and remove the existing oil filter.
2. Mounting the Adapter: Install the provided threaded nipple onto the engine block where the original oil filter was located. Then, attach the remote filter adapter to this nipple. Ensure a tight, leak-free seal.
3. Selecting a Mounting Location: Choose a suitable location for the remote filter mount. The location should be easily accessible for future oil filter changes, away from moving parts, and protected from road debris. Consider the length of the oil lines required.
4. Mounting the Remote Unit: Secure the remote filter mount unit to the chosen location using the provided mounting hardware. The unit features a 3-bolt heavy-duty mounting plate.


Figure 2: Rear view of the remote filter mount, highlighting the three mounting points for secure installation.



Figure 3: Side profile of the remote filter mount, illustrating its compact design and key dimensions for installation planning.

5. Connecting Oil Lines: Attach appropriate oil-resistant hoses (not included) to the hose barbs on the remote filter mount and the adapter on the engine block. Ensure the "IN" and "OUT" ports are correctly connected according to your engine's oil flow direction. Secure all hose connections with high-quality hose clamps to prevent leaks.
6. Installing Oil Filter: Thread a new oil filter onto the remote filter mount. Ensure the filter is compatible with the 3/4-16 inch center thread.


Figure 4: Illustrative diagram showing how an oil filter attaches to the remote filter mount. Note: Actual part may differ slightly.

7. Refilling Oil: Refill the engine with the manufacturer-recommended amount and type of engine oil.
8. Leak Check: Start the engine and immediately check for any oil leaks around the adapter, hoses, and remote filter mount. If leaks are detected, shut off the engine, allow it to cool, and re-tighten connections or replace faulty components.

Note: The provided video is an independent review and installation example by an influencer, not an official installation guide from Derale. While it demonstrates a real-world application, always refer to this manual and professional advice for official installation procedures.

Operating Instructions

Once installed, the remote filter mount operates as an integral part of your engine's oil lubrication system. No special operating procedures are required beyond standard engine operation. Always ensure the oil filter is securely tightened and there are no leaks before driving.

Maintenance

• Oil Filter Replacement: Replace the oil filter according to your vehicle manufacturer's recommendations or more frequently under severe operating conditions. Ensure to use a compatible oil filter with a 3/4-16 inch center thread.
• Leak Inspection: Periodically inspect all connections (adapter, hoses, remote mount) for any signs of oil leaks, especially after extreme driving conditions or temperature changes.
• Hose Condition: Check the oil hoses for cracks, chafing, or deterioration. Replace hoses immediately if any damage is observed.
• Mounting Security: Verify that the remote filter mount remains securely fastened to its mounting surface.

Troubleshooting

Specifications

• Model: 15708
• Material: Cast Aluminum
• Finish: Polished
• Ports: 1/2 inch NPT Female Ports
• Center Thread: 3/4-16 inch
• Mounting: 3-bolt heavy duty mounting plate
• Fit Type: Universal Fit
• Item Weight: 372 g
• Country of Origin: China

Warranty and Support

For warranty information and technical support, please refer to the official Derale website or contact their customer service directly. Keep your purchase receipt as proof of purchase.