1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Kimberly-Clark 09507 in-Sight JRT Jr. Tissue Dispenser. Please read this manual thoroughly before use to ensure proper function and longevity of the product. This dispenser is designed for use with JRT Jr. (Jumbo Roll Tissue Junior) rolls, providing a reliable and efficient solution for high-traffic restrooms.
Image 1.1: Kimberly-Clark 09507 in-Sight JRT Jr. Tissue Dispenser. This image shows the dispenser's translucent smoke-colored cover, allowing visibility of the tissue roll inside. It is designed for wall mounting.
2. Safety Information
Please observe the following safety precautions:
- Ensure the dispenser is securely mounted to a stable wall surface to prevent falling.
- Do not overload the dispenser with incorrect tissue roll sizes.
- Keep hands and fingers clear of moving parts during loading and operation.
- Use only recommended cleaning agents to avoid damage to the dispenser material.
- This product is intended for commercial or institutional use.
3. Setup and Installation
3.1 Package Contents
Verify that all components are present before beginning installation:
- Kimberly-Clark 09507 in-Sight JRT Jr. Tissue Dispenser (1 unit)
- Mounting hardware (screws and anchors)
- Dispenser key (for opening and locking)
3.2 Mounting Instructions
The dispenser is designed for screw-in installation.
- Select Location: Choose a suitable wall location, ensuring it is at an appropriate height and clear of obstructions.
- Mark Drilling Points: Hold the dispenser against the wall at the desired mounting height. Use a pencil to mark the locations for the mounting screws through the pre-drilled holes on the back plate of the dispenser.
- Drill Holes: Using an appropriate drill bit for your wall type (e.g., masonry, drywall), drill pilot holes at the marked locations. If installing into drywall, insert the provided wall anchors.
- Secure Dispenser: Align the dispenser with the drilled holes. Insert the screws through the dispenser's mounting holes and into the wall anchors or studs. Tighten the screws until the dispenser is firmly secured to the wall. Do not overtighten.
- Test Stability: Gently pull on the dispenser to ensure it is securely mounted and does not wobble.
3.3 Loading Tissue Rolls
- Open Dispenser: Insert the provided key into the lock mechanism located on the top or side of the dispenser. Turn the key to unlock and open the front cover.
- Insert Main Roll: Place a new JRT Jr. tissue roll onto the main spindle inside the dispenser. Ensure the tissue feeds from the bottom of the roll.
- Thread Tissue: Pull the leading edge of the tissue paper down through the dispensing slot at the bottom of the dispenser.
- Load Stub Roll (if applicable): If a stub roll (partially used roll) is present, place it on the auxiliary stub roll holder. The dispenser is designed to utilize the stub roll completely before switching to the new main roll.
- Close and Lock: Close the front cover of the dispenser firmly until it clicks shut. Turn the key to lock the dispenser. Remove the key.
4. Operating Instructions
4.1 Dispensing Tissue
To dispense tissue, simply pull the exposed end of the tissue paper downwards from the dispensing slot. The dispenser is designed for smooth, single-sheet or controlled dispensing, depending on the tissue type used.
4.2 Monitoring Tissue Levels (in-Sight Feature)
The "in-Sight" feature refers to the translucent smoke-colored cover of the dispenser. This design allows maintenance staff to visually monitor the remaining tissue level without needing to open the dispenser. This helps in efficient refilling and prevents unexpected run-outs.
5. Maintenance
5.1 Cleaning
Regular cleaning will help maintain the appearance and hygiene of your dispenser.
- Wipe the exterior surfaces with a soft, damp cloth and a mild, non-abrasive cleaner.
- Avoid using harsh chemicals, abrasive pads, or solvents, as these can damage the plastic finish.
- Ensure the dispenser is dry after cleaning.
5.2 Refilling
Refill the dispenser as described in Section 3.3 "Loading Tissue Rolls" when the main roll is depleted or when the stub roll is in use and a new main roll is required.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Tissue not dispensing smoothly. |
|
|
| Dispenser cover will not close or lock. |
|
|
| Dispenser feels loose on the wall. |
|
|
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | KCC09507 |
| Brand | Kimberly-Clark |
| Material | Plastic |
| Color | Trans Smoke (Translucent Smoke) |
| Dimensions (W x D x H) | Approximately 13 22/25" x 5 3/4" x 16" (35.3cm x 14.6cm x 40.6cm) |
| Installation Type | Screw-In (Wall Mount) |
| Compatible Tissue | JRT Jr. (Jumbo Roll Tissue Junior) |
| Weight | Approximately 4 Pounds (1.8 kg) |
8. Warranty and Support
8.1 Product Warranty
Kimberly-Clark Professional products are manufactured to high-quality standards. For specific warranty details regarding your 09507 in-Sight JRT Jr. Tissue Dispenser, please refer to the warranty information provided at the time of purchase or visit the official Kimberly-Clark Professional website. Keep your proof of purchase for warranty claims.
8.2 Customer Support
If you encounter any issues or have questions not covered in this manual, please contact Kimberly-Clark Professional customer support. Contact information can typically be found on the product packaging or the official Kimberly-Clark Professional website.
Website: www.kcprofessional.com