1. Introduction and Overview
The Skylink G6-T2 is a compact, two-button keychain transmitter designed to operate up to two compatible garage door openers. This device utilizes rolling code technology for enhanced security. Its small size allows for convenient carrying in a pocket or purse, or it can be mounted in a vehicle using the included accessories. The G6-T2 is compatible with Skylink EQ-IQ-Series Garage Door openers. For non-Skylink garage door openers, a Skylink Smart Button Receiver model GB-318 (sold separately) is required for operation.
Figure 1: Skylink G6-T2 Two-Button Keychain Transmitter (Black). This compact remote features two control buttons and a red indicator light.
2. Package Contents
Verify that all items are present in the package:
- Skylink G6-T2 Two-Button Keychain Transmitter (available in assorted colors, including black and gray)
- One 12V Alkaline Battery (pre-installed or included separately)
- Visor Clip
- Mounting Accessories
Figure 2: Skylink G6-T2 Transmitter shown alongside its included visor clip and mounting bracket.
3. Product Features
- Compact two-button design for keychain portability.
- Operates up to two Skylink EQ-IQ-Series Garage Door openers.
- Incorporates Rolling Code Technology for enhanced security.
- Includes a visor clip and additional mounting accessories for versatile placement.
- Powered by a long-life Alkaline battery (12V).
4. Setup and Programming
The G6-T2 transmitter must be programmed to your garage door opener or a compatible receiver to function. The programming method varies depending on your specific garage door opener model or if you are using a Skylink Smart Button Receiver (GB-318).
4.1. Battery Installation/Verification
The G6-T2 uses one 12V Alkaline battery. Ensure the battery is correctly installed and functional before programming. If the red indicator light on the transmitter does not illuminate when a button is pressed, the battery may need replacement (refer to Section 6).
4.2. Programming to a Skylink EQ-IQ-Series Garage Door Opener
- Locate the Learn button on your Skylink EQ-IQ-Series garage door opener motor unit. The location of this button may vary; consult your garage door opener's instruction manual for precise details.
- Press and release the Learn button on the garage door opener. The indicator light on the opener will typically illuminate or flash, indicating it is in programming mode.
- Within 30 seconds, press and hold the desired button on your G6-T2 transmitter for approximately 2-3 seconds.
- Release the button. The garage door opener's light may flash or turn off, indicating successful programming.
- Test the transmitter by pressing the programmed button. The garage door should activate.
4.3. Programming with a Skylink Smart Button Receiver (GB-318)
If your garage door opener is not a Skylink EQ-IQ-Series model, you will need a Skylink Smart Button Receiver (GB-318) to enable compatibility with the G6-T2 transmitter. Refer to the instruction manual provided with your GB-318 receiver for specific programming steps. Generally, the process involves:
- Ensure the GB-318 receiver is properly installed and connected to your garage door opener.
- Activate the programming mode on the GB-318 receiver (usually by pressing a Learn button).
- Press the desired button on your G6-T2 transmitter to pair it with the GB-318.
- Test the operation.
Important: Always refer to the specific instruction manual for your garage door opener or the Skylink Smart Button Receiver (GB-318) for detailed and accurate programming procedures.
5. Operation
Once programmed, operating the G6-T2 transmitter is straightforward:
- Press the programmed button on the transmitter to activate your garage door opener.
- The red indicator light on the transmitter will illuminate briefly when a button is pressed, confirming signal transmission.
- If two garage door openers are programmed, use the corresponding button for each opener.
6. Battery Replacement
The G6-T2 transmitter is powered by one 12V Alkaline battery. If the operating range decreases significantly or the red indicator light does not illuminate when a button is pressed, it is time to replace the battery.
Replacement Procedure:
- Carefully open the casing of the G6-T2 transmitter. This may involve gently prying apart the two halves of the remote, often at a seam.
- Remove the old 12V Alkaline battery.
- Insert a new 12V Alkaline battery, ensuring the correct polarity (+ and -) is observed.
- Snap the casing back together securely.
- Test the transmitter to ensure proper function.
Note: Dispose of old batteries according to local regulations.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Transmitter does not activate garage door. | Not programmed correctly; Dead or low battery; Out of range; Incompatible opener. | Re-program the transmitter (Section 4); Replace battery (Section 6); Move closer to the garage door opener; Ensure compatibility or use GB-318 receiver. |
| Red indicator light does not illuminate. | Dead or incorrectly installed battery. | Replace battery, ensuring correct polarity (Section 6). |
| Reduced operating range. | Low battery; Radio interference. | Replace battery (Section 6); Check for sources of interference near the garage door opener. |
| Transmitter works intermittently. | Low battery; Weak signal; Interference. | Replace battery (Section 6); Ensure clear line of sight to opener; Check for interference. |
8. Specifications
| Model Number | G6-T2 |
| Brand | SKYLINK |
| Dimensions (L x W x H) | 2.5 x 1.5 x 0.75 inches |
| Weight | 1.83 ounces |
| Battery Type | 1 x 12V Alkaline (included) |
| Average Battery Life | 4320 Hours |
| Compatibility | Skylink EQ-IQ-Series Garage Door openers, Skylink Smart Button Receiver model GB-318 |
| Technology | Rolling Code |
| Color | Assorted (e.g., Gray, Black) |
9. Warranty and Support
9.1. Warranty Information
The Skylink G6-T2 Two-Button Keychain Transmitter comes with a 1-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, accident, alteration, or unauthorized repair.
9.2. Customer Support
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact Skylink customer support. Refer to the official Skylink website or product packaging for current contact information.
