Tycon Systems EZBR-Ultra5 Point-to-Point Bridge System User Manual

Product Overview

The Tycon Systems EZBR-Ultra5 is a high-capacity 100Mbps and high-power 250mW outdoor wireless bridge system. It operates in the 5GHz unlicensed spectrum, designed to establish ultra-high bandwidth connections between two buildings up to 4 miles or more apart, provided there is a good line of sight.

Image: The EZBR-Ultra5 system components. This includes two complete bridge units, each comprising a dish antenna and mounting hardware. Also shown are the necessary power injectors/adapters and Ethernet cables for connecting the units. The image also displays antenna radiation patterns (Azimuth and Elevation) indicating the directional nature of the wireless signal.

Key Features

• Networking Type: Bridge
• Data Transfer Rate: 100 Mbps
• Operating Frequency: 5 GHz Radio Frequency
• High Power Output: 250mW for extended range
• Plug and Play: Designed for easy setup and deployment.
• Long Range Capability: Connects buildings up to 4 miles or more with clear line of sight.

Setup Guide

This section outlines the steps required to set up your EZBR-Ultra5 Point-to-Point Bridge System.

1. Unpacking and Inspection

1. Carefully unpack all components from the packaging.
2. Verify that all items listed in the packing list are present.
3. Inspect all components for any signs of physical damage. If any damage is found, contact your vendor immediately.

2. Site Selection and Line of Sight

For optimal performance, ensure a clear line of sight between the two bridge units. Obstructions such as trees, buildings, or hills will degrade performance or prevent connection.

• Choose mounting locations that provide an unobstructed path.
• Consider mounting the units as high as possible to clear potential obstacles.

3. Mounting the Units

The EZBR-Ultra5 units are designed for outdoor pole or wall mounting.

1. Attach the mounting bracket to the rear of the antenna unit.
2. Securely fasten the unit to a sturdy pole or wall using appropriate hardware (not included).
3. Ensure the unit is firmly fixed and can withstand wind and environmental conditions.

4. Cabling and Power Connection

1. Connect one end of the Ethernet cable to the EZBR-Ultra5 unit's Ethernet port.
2. Connect the other end of the Ethernet cable to the "PoE" port of the included Power over Ethernet (PoE) injector.
3. Connect a second Ethernet cable from the "LAN" port of the PoE injector to your network device (e.g., router, switch, or computer).
4. Plug the power adapter into the PoE injector and then into a suitable power outlet.
5. Repeat these steps for the second EZBR-Ultra5 unit.

Operating Instructions

Once the physical setup is complete, the EZBR-Ultra5 units are designed for "Plug and Play" operation, meaning they should automatically establish a link.

1. Power On

After connecting power, the units will power on and begin their boot sequence. This may take a few minutes.

2. Link Establishment

The two EZBR-Ultra5 units are pre-configured to find each other and establish a wireless bridge link. Indicators (e.g., LEDs) on the units will typically show the status of the link.

• Refer to the unit's LED indicators for link status. A solid green or blue light usually indicates a successful connection.
• If the link does not establish, verify line of sight and power connections.

3. Network Integration

Once the bridge is established, your two networks (or devices) connected to each EZBR-Ultra5 unit will be able to communicate as if they were on the same local network segment.

• Ensure your connected devices have appropriate IP addresses (DHCP or static) for your network.
• Test network connectivity by pinging devices across the bridge.

Maintenance

The EZBR-Ultra5 system is designed for robust outdoor operation with minimal maintenance.

• Regular Inspection: Periodically inspect the units and cabling for any physical damage, loose connections, or signs of wear due to weather exposure.
• Clear Line of Sight: Ensure that the line of sight between the two units remains clear. Trim any growing vegetation that might obstruct the path.
• Cleaning: If necessary, gently clean the exterior of the units with a soft, damp cloth. Do not use harsh chemicals or abrasive materials.
• Firmware Updates: Check the Tycon Systems website periodically for any available firmware updates. Follow the instructions provided by the manufacturer for any update procedures.

Troubleshooting

This section provides solutions to common issues you might encounter with your EZBR-Ultra5 system.

Specifications

Warranty and Support

For warranty information and technical support, please refer to the official Tycon Systems website or contact their customer service directly.

• Official Website: www.tyconsystems.com (Note: This is a placeholder URL as the actual support URL is not provided in the input. Users should verify the correct URL.)
• Customer Service: Refer to the website for contact details, including phone numbers and email support.
• Keep your purchase receipt as proof of purchase for warranty claims.