1. Introduction
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your EUROFRED Professional Glass Washer, model LV 40. Please read this manual thoroughly before operating the appliance and keep it for future reference. Proper use and maintenance will ensure optimal performance and extend the lifespan of your glass washer.
2. Safety Instructions
Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and injury to persons.
- Read all instructions before using the appliance.
- Ensure the appliance is properly grounded.
- Do not operate the appliance with a damaged cord or plug.
- Keep children away from the appliance during operation.
- Use only detergents and rinse aids specifically designed for commercial glass washers.
- Disconnect power before performing any maintenance or cleaning.
- Do not spray water directly onto electrical components.
3. Setup and Installation
Proper installation is crucial for the performance and safety of your glass washer. It should be installed by a qualified technician.
3.1 Unpacking
Carefully remove the appliance from its packaging. Inspect for any damage incurred during transit. Report any damage to your supplier immediately.
3.2 Positioning
Place the glass washer on a stable, level surface capable of supporting its weight when full. Ensure adequate ventilation around the unit.
3.3 Water Connection
Connect the water inlet to a potable water supply using a 3/4 inch connection. Ensure the water pressure is between 2 and 4 bar. An external water softener may be required depending on water hardness.
3.4 Drainage Connection
Connect the drain hose to a suitable drainage system. The drain connection diameter is 28 mm. Ensure the drain hose has a continuous downward slope to prevent standing water.
3.5 Electrical Connection
Connect the appliance to a dedicated electrical supply. The unit requires 220V, 2-phase power. Ensure the electrical installation complies with local regulations and is properly grounded.
4. Operating Instructions
Follow these steps for efficient operation of your EUROFRED LV 40 glass washer.
4.1 Initial Start-up
- Ensure all connections (water, drain, electrical) are secure.
- Open the water supply valve.
- Switch on the main power to the machine. The tank will begin to fill automatically.
- Allow the machine to heat up to the operating temperatures (wash: 55°C, rinse: 85°C). This may take several minutes.
4.2 Loading Glasses
Place glasses in the basket, ensuring they are not overlapping and water can reach all surfaces. Do not overload the basket.
4.3 Washing Cycle
- Close the door securely.
- Press the start button to initiate the wash cycle. The total cycle duration is approximately 120 seconds, with a 17-second rinse phase.
- Wait for the cycle to complete.
- Open the door and remove the clean glasses. Allow them to air dry if necessary.
4.4 Detergent and Rinse Aid
Ensure the detergent and rinse aid dispensers are filled. Refer to the detergent manufacturer's instructions for correct dosage. The machine automatically dispenses the correct amount during the cycle.
5. Maintenance
Regular maintenance ensures the longevity and efficiency of your glass washer.
5.1 Daily Cleaning
- At the end of each day, switch off the machine and disconnect from power.
- Drain the wash tank.
- Remove and clean the filters and wash arms. Rinse them under running water to remove food debris and scale.
- Wipe down the interior and exterior surfaces with a damp cloth and mild detergent.
- Leave the door slightly ajar to allow the interior to air dry and prevent odors.
5.2 Weekly / Monthly Checks
- Inspect wash and rinse nozzles for blockages. Clean if necessary.
- Check for any leaks around connections.
- Descaling: Depending on water hardness, periodic descaling may be required. Use a commercial descaling agent suitable for dishwashers and follow the manufacturer's instructions.
6. Troubleshooting
This section provides solutions to common issues. For problems not listed here, contact qualified service personnel.
| Problem | Possible Cause | Solution |
|---|---|---|
| Machine does not start | No power supply; Door not closed properly; Main switch off. | Check power connection; Ensure door is fully latched; Turn on main switch. |
| Poor washing results | Clogged wash arms/nozzles; Insufficient detergent; Water temperature too low; Overloaded basket. | Clean wash arms/nozzles; Check detergent level; Allow machine to heat up; Do not overload. |
| Water not draining | Drain filter clogged; Drain hose kinked or blocked. | Clean drain filter; Check drain hose for obstructions. |
| Machine leaking | Loose connections; Damaged door seal. | Check and tighten connections; Inspect and replace door seal if damaged. |
7. Specifications
Technical data for the EUROFRED Professional Glass Washer LV 40.
| Feature | Value |
|---|---|
| Wash Capacity | 30 baskets/hour |
| Useful Wash Height | 290 mm |
| Tank Capacity | 20 liters |
| Boiler Capacity | 3.4 liters |
| Inlet Water Temperature (Max) | 50°C |
| Wash Temperature | 55°C |
| Rinse Temperature | 85°C |
| Total Cycle Duration | 120 seconds |
| Rinse Duration | 17 seconds |
| Voltage/Phase | 220V / 2 Phase |
| Boiler Heater Power | 2400 W |
| Tank Heater Power | 1850 W |
| Total Electrical Power | 2650 W |
| Wash Pump Power | 250 W |
| Water Inlet Connection | 3/4 inch |
| Drain Connection | 28 mm |
| Water Pressure (Min/Max) | 2 / 4 bar |
| Water Consumption per Cycle | 2 liters |
| External Width | 480 mm |
| External Depth | 530 mm |
| External Height | 720 mm |
| Net Weight | 45 kg |
| Gross Weight | 48 kg |
8. Warranty and Support
This EUROFRED appliance comes with a manufacturer's warranty. Please refer to the warranty card included with your purchase for specific terms and conditions. For technical support, spare parts, or service inquiries, please contact your authorized EUROFRED dealer or service center. Ensure you have your model number (LV 40) and purchase date available when contacting support.
Note: No product images or videos were provided in the input data to be embedded in this manual.