TACWISE 0396
TACWISE 18G/25mm Galvanised Brad Nails
Model: 0396
Product Overview
This image shows the packaging for TACWISE 18G/25mm 1 inch Galvanised Brad Nails. The blue and yellow box indicates a pack of 5,000 nails. The packaging highlights compatibility with Tacwise 18G Nailers, Stanley BT1300, Senco AY/AX, Paslode F18/C140, BeA SK300 Range, and other 18G Brad Nailers.
TACWISE 18G/25mm Galvanised Brad Nails are premium quality fasteners designed for a wide range of woodworking and construction applications. Manufactured from high-grade materials, these nails provide a strong, reliable hold and are coated with galvanisation for enhanced rust resistance. They are suitable for both semi-professional and DIY projects.
Key Features:
- Premium quality 18 gauge brad nails for strong holding power.
- Pack of 5,000 galvanised steel nails, 18G/25mm (1 inch) in size.
- Rust-resistant galvanised coating for durability in various environments.
- Ideal for joinery, trim work, finish carpentry, sub-flooring, kitchen assembly, and other woodworking applications.
- Compatible with a wide range of 18G brad nailers, including Tacwise 181EL/S, 191EL/S, Duo 35, Duo 50, 1183, Ranger EL-PRO, C1832V, DGN50V, 1326, and equivalents like Stanley Type J, Rapid Type 8, and Arrow 18GA brad nails.
Setup and Compatibility
These brad nails are designed for use with compatible 18-gauge brad nailers. Before use, always verify the compatibility of your specific nailer model with 18G/25mm nails. Refer to your nailer's instruction manual for proper loading procedures and safety guidelines.
Loading Instructions (General):
- Ensure the brad nailer is disconnected from its power source (air compressor, battery, or power outlet) before loading.
- Open the nail magazine of your brad nailer according to its specific design.
- Insert the strip of TACWISE 18G/25mm brad nails into the magazine, ensuring the nails are oriented correctly (points facing forward).
- Close the magazine securely until it latches.
- Reconnect the nailer to its power source and perform a test fire on a scrap piece of material to ensure proper feeding and depth setting.
Operating Instructions
Once loaded into a compatible brad nailer, these nails are ready for use in various fastening applications. Always wear appropriate personal protective equipment (PPE), including safety glasses, when operating a nailer.
Application Tips:
- Material Preparation: Ensure the work surface is clean and free of debris.
- Nailer Settings: Adjust the depth setting on your brad nailer to achieve the desired flush or countersunk finish for the nail head. Test on scrap material first.
- Placement: Position the nailer firmly against the workpiece. For best results, drive nails perpendicular to the surface.
- Spacing: Space nails appropriately to provide adequate holding power without splitting the material.
- Safety: Keep hands and body parts clear of the nailer's discharge area. Never point the nailer at yourself or others.
Maintenance and Storage
Proper maintenance and storage will ensure the longevity and performance of your TACWISE Galvanised Brad Nails.
Storage:
- Store nails in their original packaging or a sealed container to protect them from moisture and humidity.
- Keep nails in a cool, dry place to prevent corrosion, even with the galvanised coating.
- Avoid storing nails in environments with extreme temperature fluctuations.
Inspection:
- Before loading, inspect nail strips for any damage, bending, or excessive rust that could cause feeding issues in your nailer.
- Discard any damaged or heavily corroded nails.
Troubleshooting
While TACWISE nails are designed for consistent performance, issues can sometimes arise during use. Most problems are related to the nailer itself or improper technique.
Common Issues and Solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Nails not feeding | Damaged nail strip, incorrect nail size, dirty magazine, low air pressure (for pneumatic nailers) | Inspect nail strip, ensure correct nail size, clean nailer magazine, check air pressure/battery charge. |
| Nails bending or not fully seating | Incorrect depth setting, hitting dense material, dull driver blade (nailer issue) | Adjust depth setting, pre-drill pilot holes for very dense wood, service nailer if driver blade is worn. |
| Nailer jamming | Damaged nails, foreign debris in magazine, worn nailer components | Clear jam according to nailer manual, inspect nails, clean nailer. |
For persistent issues, consult the user manual of your specific brad nailer or contact the nailer manufacturer's support.
Specifications
| Attribute | Detail |
|---|---|
| Model Number | 0396 |
| Nail Type | 18 Gauge Brad Nails |
| Length | 25 mm (1 inch) |
| Quantity | 5,000 nails per pack |
| Material | Galvanised Steel |
| Color | Silver |
| Exterior Finish | Zinc |
| Item Weight (packaging) | 0.64 ounces (approx. 18.14 g) |
| Product Dimensions (packaging) | 5.51 x 1.26 x 2.44 inches |
| Manufacturer | Tacwise |
| UPC | 791429355207 |
Warranty and Support
TACWISE 18G/25mm Galvanised Brad Nails are manufactured to high-quality standards. For any concerns regarding the product's quality or performance, please contact your retailer or the manufacturer directly. Specific warranty information for consumable items like nails may vary by region and retailer.
For technical support related to the use of these nails with specific tools, please refer to the documentation provided by your brad nailer's manufacturer.