Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Kingston Brass CC2085 Vintage Clawfoot Tub Waste and Overflow Drain. Please read all instructions carefully before beginning installation to ensure proper function and longevity of your product.
Image: Kingston Brass CC2085 Vintage Clawfoot Tub Drain, Oil Rubbed Bronze finish. This image shows the complete drain assembly, including the overflow cover, waste pipe, and drain stopper.
Product Features:
- Material: Fabricated from solid brass for enhanced reliability and durability.
- Gauge: 20 gauge construction.
- Drain Operation: Convenient lift and turn drain stopper mechanism.
- Thread Length: 1-1/2 inch thread length.
- Finish: Corrosion-resistant Oil Rubbed Bronze finish.
- Application: Designed for clawfoot tubs and exposed drain applications.
Safety Information
Please observe the following safety precautions during installation and use:
- Always turn off the main water supply before beginning any plumbing work.
- Wear appropriate personal protective equipment, such as safety glasses and gloves.
- Ensure all connections are properly sealed to prevent leaks.
- If you are unsure about any step, consult a qualified plumber.
- Keep small parts away from children.
Package Contents
Verify that all components are present before starting installation:
- Lift and Turn Drain Stopper Assembly
- Overflow Cover
- Overflow Pipe
- Waste Pipe
- Connecting Nuts and Washers
- Gaskets (including two different thickness gaskets for overflow)
Setup and Installation
Follow these steps for proper installation of your clawfoot tub drain. Refer to the diagram below for component identification and dimensions.
Image: Detailed technical drawing of the Kingston Brass CC2085 Clawfoot Tub Waste & Overflow Drain, showing all components and critical dimensions for installation. This includes the drain stopper, overflow cover, and connecting pipes.
- Prepare the Tub: Ensure the tub's drain and overflow holes are clean and free of debris.
- Install Drain Stopper Assembly:
- Apply plumber's putty or silicone sealant around the underside of the drain flange (the part that sits inside the tub).
- Insert the drain stopper assembly through the drain hole from the inside of the tub.
- From underneath the tub, secure the drain assembly with the rubber washer, friction washer, and lock nut. Tighten firmly but do not overtighten.
- Install Overflow Assembly:
- Attach the overflow cover to the overflow pipe, ensuring a gasket is properly seated between the tub and the overflow cover. Use the appropriate thickness gasket for your tub.
- Connect the overflow pipe to the overflow opening on the tub.
- Secure the overflow cover with the provided screw(s).
- Connect Waste and Overflow Pipes:
- Assemble the waste pipe and overflow pipe using the compression fittings. The pipes are designed to be cut to length if necessary to fit your specific tub dimensions. Refer to the technical drawing for typical dimensions (e.g., 12"~12-5/8" for horizontal waste pipe, 16-1/4" to 22-5/8" for vertical overflow pipe).
- Ensure all connections are aligned and tightened securely to prevent leaks. The compression couplings require careful attention to alignment and tightening.
- Connect to House Drain: Connect the assembled drain system to your home's waste plumbing. Ensure a proper seal at this connection.
- Test for Leaks: Fill the tub with water and check all connections for any signs of leakage. Tighten any leaking connections as needed.
Note: Antique bathtubs may have different dimensions than modern ones. You may need to adjust the height of the tub or find alternative solutions if there is a mismatch between the tub and the drain assembly, particularly concerning the floor opening.
Operation
The Kingston Brass CC2085 drain features a simple lift and turn stopper mechanism:
- To Close the Drain: Gently push down on the stopper and twist it clockwise until it seals the drain opening.
- To Open the Drain: Twist the stopper counter-clockwise and lift it to allow water to drain from the tub.
Maintenance
Proper care will help maintain the finish and function of your drain assembly:
- Cleaning: Clean the drain assembly regularly with a soft cloth and mild soap. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the Oil Rubbed Bronze finish.
- Drain Clogs: Periodically remove the stopper and clean any hair or debris that may accumulate in the drain opening to prevent clogs.
- Finish Care: For the Oil Rubbed Bronze finish, avoid prolonged contact with acidic substances or strong detergents.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Drain Leaks | Loose connections, improperly seated gaskets, damaged seals. | Check and tighten all nuts. Ensure gaskets are correctly positioned. Replace damaged seals if necessary. Reapply plumber's putty if needed. |
| Drain Stopper Not Sealing | Debris under stopper, stopper mechanism malfunction. | Remove stopper and clean thoroughly. Check if the lift and turn mechanism is operating freely. |
| Slow Draining | Partial clog in waste pipe. | Remove stopper and clear any visible debris. Use a drain snake if necessary. Avoid chemical drain cleaners that may damage the finish. |
Specifications
| Model Number: | CC2085 |
| Brand: | Kingston Brass |
| Material: | Brass |
| Color/Finish: | Oil Rubbed Bronze |
| Item Weight: | 5.07 Pounds |
| Drain Type: | Lift and Turn |
| Thread Length: | 1-1/2 inches |
| Gauge: | 20 Gauge |
| UPC: | 663370036613 |
Warranty and Support
For parts, technical assistance, or warranty inquiries, please contact Kingston Brass directly.
- Customer Service: 1-877-252-7277
- Website: www.kingstonbrass.com
Kingston Brass products are designed for long-lasting durability. Refer to the manufacturer's website for specific warranty details applicable to your product.