Product Overview
This manual provides instructions for the Tenergy 9.6V (8S) NiMH/NiCd RC Battery Charger, designed for use with RC hobbies. It features a 400mA AC plug and a standard Tamiya connector. This charger is specifically for 9.6V NiMH/NiCd battery packs and is not compatible with LiPo batteries or other voltage battery types.
Image: The Tenergy 9.6V NiMH/NiCd RC Battery Charger with its standard Tamiya connector.
Safety Instructions
- Only use this charger with 9.6V (8S) NiMH or NiCd battery packs. Do not attempt to charge LiPo batteries or any other battery chemistry.
- This charger is not compatible with Spike the Dinosaur or similar toys requiring specific charging protocols.
- Ensure the battery connector is a standard Tamiya type. Incompatible connectors may cause damage.
- Do not leave charging batteries unattended.
- Keep the charger and battery away from flammable materials.
- Do not expose the charger to moisture or extreme temperatures.
- If the charger or battery shows signs of damage, discontinue use immediately.
Setup
Before first use, inspect the charger and battery for any visible damage. Ensure the battery pack is a 9.6V NiMH or NiCd type with a standard Tamiya connector.
- Locate a standard AC power outlet (100-240V).
- Plug the charger's AC plug into the power outlet. The LED indicator on the charger will illuminate.
- Connect the standard Tamiya connector from your 9.6V NiMH/NiCd battery pack to the charger's output connector. Ensure a secure connection.
Image: Diagram showing the dimensions of a standard Tamiya connector, emphasizing compatibility. This charger is only compatible with white standard Tamiya connectors, not mini Tamiya connectors.
Image: The Tenergy charger plugged into a power strip, ready to connect to a battery pack.
Operating Instructions
Charging Your Battery
Once the charger is plugged into an AC outlet and connected to a compatible 9.6V NiMH/NiCd battery pack, the charging process will begin automatically.
- LED Indicator: The charger features a simple LED indicator to show charging status.
- Solid Red: Indicates the battery is currently charging.
- Solid Green: Indicates the battery is fully charged.
Image: Close-up of the charger showing a red LED for charging and a green LED for fully charged status.
For a 2000mAh battery pack, the estimated charge time from empty is approximately 5-6 hours at a 400mA charging speed. Charging times may vary based on battery capacity and discharge level.
Image: The Tenergy charger connected to a 9.6V 2000mAh NiMH battery pack, illustrating the charging process.
Voltage Compatibility
This charger is designed for 9.6V (8S) NiMH and NiCd battery packs. Always verify your battery's voltage and chemistry before connecting to prevent damage.
Image: Two different styles of 9.6V (8S) NiMH battery packs, demonstrating the charger's voltage compatibility.
Maintenance
- Keep the charger clean and free from dust and debris. Use a dry cloth for cleaning.
- Store the charger in a cool, dry place when not in use.
- Avoid wrapping the cable too tightly around the charger to prevent wire damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Charger LED does not light up. | No power from AC outlet; charger or cable damaged. | Check AC outlet with another device. Inspect charger and cable for damage. If damaged, discontinue use. |
| Charger LED remains red after extended charging. | Battery not fully charged; faulty battery; charger malfunction. | Allow more time for charging. Test battery with another compatible charger if available. Contact support if issue persists. |
| Charger LED is green but battery is not fully charged. | Charger malfunction; battery issue. | Ensure battery is properly connected. If the issue persists, the charger may be faulty. |
| Charger gets excessively hot. | Overload; internal fault. | Immediately disconnect the charger and battery. Do not use if it overheats. Contact support. |
Specifications
- Model Number: 01009
- Input Voltage: 100-240V AC
- Output Voltage: 12 Volts
- Charging Current: 400mA
- Compatible Battery Types: NiMH, NiCd
- Compatible Battery Voltage: 9.6V (8S)
- Connector Type: Standard Tamiya
- Item Weight: 3.21 ounces (0.2 Pounds)
- Package Dimensions: 3.82 x 1.5 x 1.1 inches
- Certification: CE Compliant
Warranty and Support
This Tenergy charger includes a 12-month warranty from the date of purchase. For warranty claims, technical support, or any questions regarding the product, please contact Tenergy Corporation directly. Refer to the product packaging or the official Tenergy website for the most current contact information.
Product Videos
Tenergy 9.6V Charger Overview
Video: An official product video from Tenergy Corporation demonstrating the features and use of the 9.6V charger for RC hobbies. This video highlights voltage compatibility and ease of use.