Schonbek Bagatelle Collection 10 1/2" Crystal Ceiling Light Instruction Manual

1. Introduction

Thank you for choosing the Schonbek Bagatelle Collection 10 1/2" Crystal Ceiling Light. This fixture is designed to provide elegant illumination for various indoor spaces. This manual contains important information regarding the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions thoroughly before beginning installation and retain them for future reference.

Figure 1: Full view of the Schonbek Bagatelle Collection Crystal Ceiling Light.

2. Important Safety Information

WARNING: Risk of electric shock. Disconnect power at the fuse box or circuit breaker before installation or servicing. Consult a qualified electrician if you are unsure about the installation process.

• Read all instructions carefully before proceeding.
• Ensure all electrical connections comply with local codes and ordinances, as well as the National Electric Code (NEC).
• Do not install this fixture in wet or damp locations. This product is designed for indoor use only.
• Use only bulbs of the specified type and wattage (B10-3, 40W Max). Exceeding the maximum wattage can cause overheating and damage to the fixture or create a fire hazard.
• Handle crystal components with care to prevent breakage.
• Proposition 65 Warning: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

3. Package Contents

Carefully unpack your fixture and check that all parts are included. If any parts are missing or damaged, do not attempt to assemble or install the fixture. Contact customer service for assistance.

• Schonbek Bagatelle Crystal Ceiling Light Fixture (1)
• Mounting Hardware Kit (1)
• Installation Instructions (This manual)

Note: Light bulbs (B10-3, 40W Max) are not included and must be purchased separately.

4. Setup and Installation

This fixture is designed for semi-flush mount installation. No assembly is required for the main fixture body, but crystal elements may need to be attached.

Tools Required (Not Included):

• Phillips Head Screwdriver
• Wire Strippers
• Electrical Tape
• Ladder

Installation Steps:

1. Turn Off Power: Locate the circuit breaker or fuse box that controls the power to the ceiling outlet box. Turn off the power completely before starting installation.
2. Prepare Mounting: If replacing an existing fixture, carefully remove it. Attach the mounting bracket (from the hardware kit) to the ceiling outlet box using the provided screws. Ensure the bracket is securely fastened.
3. Make Electrical Connections:
   • Connect the bare copper ground wire from the fixture to the ground wire from the outlet box (usually bare copper or green) using a wire nut.
   • Connect the white wire from the fixture to the white (neutral) wire from the outlet box using a wire nut.
   • Connect the black wire from the fixture to the black (hot) wire from the outlet box using a wire nut.
   • Secure all wire connections with electrical tape.
4. Mount the Fixture: Carefully lift the fixture and align the holes on the fixture canopy with the screws on the mounting bracket. Secure the fixture to the mounting bracket using the decorative nuts or screws provided.
5. Install Bulbs: Screw in three B10-3 base bulbs (max 40W each) into the sockets. Do not overtighten.
6. Attach Crystal Elements: If any crystal elements are packaged separately, carefully attach them according to the diagrams provided with the fixture (if applicable). Refer to Figure 2 for an example of crystal detailing.

Figure 2: Detailed view of the crystal elements and bronze finish.

Figure 3: The Schonbek Bagatelle Ceiling Light installed in an indoor setting.

5. Operating Instructions

The Schonbek Bagatelle Ceiling Light is operated by a standard wall toggle switch (not included). Once installed and powered, simply use the wall switch to turn the light fixture on or off.

6. Maintenance

Cleaning:

• Always disconnect power before cleaning.
• To clean the crystal components, use a soft, lint-free cloth dampened with a mild glass cleaner or distilled water. Avoid abrasive cleaners or harsh chemicals, as these can damage the finish and crystal.
• For the metal finish (Heirloom Bronze), wipe with a soft, dry cloth. Do not use polishes or abrasive materials.

Bulb Replacement:

• Ensure power is turned off at the circuit breaker before replacing bulbs.
• Allow bulbs to cool completely before touching them.
• Carefully unscrew the old bulb and screw in a new B10-3 base bulb, not exceeding 40 watts.
• Restore power and test the fixture.

7. Troubleshooting

8. Specifications

9. Warranty and Support

For warranty information or technical support, please contact Schonbek customer service directly. Refer to the contact information provided with your purchase documentation or visit the official Schonbek website.