Product Overview
The Scotts Turf Builder EdgeGuard DLX Broadcast Spreader is designed for efficient and precise application of various lawn care products. It is suitable for spreading fertilizer, grass seed, granular weed killer, salt, and ice melt across areas up to 15,000 sq. ft.
Key features include:
- Scotts exclusive EdgeGuard Technology to prevent product from spreading onto non-lawn areas like landscaping, driveways, and sidewalks.
- Comes pre-calibrated and ready-to-use for immediate operation.
- Redesigned hopper and agitator for smoother product funneling and consistent coverage.
- Large capacity, holding up to 15,000 sq. ft. of product.
Image: The Scotts Turf Builder EdgeGuard DLX Broadcast Spreader, ready for use.
Setup and Assembly
The Scotts Turf Builder EdgeGuard DLX Broadcast Spreader is designed for quick and easy setup. It arrives pre-calibrated and largely assembled, requiring minimal effort before first use.
- Unpack the spreader and ensure all components are present.
- Attach the handle assembly if not already connected, securing any locking pins or bolts.
- Verify that the control cables for the EdgeGuard and flow rate are properly connected and move freely.
- The handle is designed to fold down for easy storage.
Image: The spreader is pre-calibrated and ready to use, with a fold-down handle for easy storage.
Assembly Demonstration Video
Video: This video provides a detailed comparison of Scotts Turf Builder EdgeGuard spreaders, including unboxing and assembly steps for various models.
Operating Instructions
Follow these steps for effective product application:
- Prepare: Always read and follow the directions on the label of the Scotts product you are applying. This will provide the correct spreader setting.
- Fill: Fill your spreader over a driveway or sidewalk to easily clean up any spills.
- Set: Turn the rate control dial to the correct setting specified on the product label. The spreader features a precision control panel for accurate coverage.
- Go: To apply, begin walking at a steady pace and then squeeze the trigger to release the product. Release the trigger when making turns or stopping to prevent over-application.
Image: Visual guide illustrating the four simple steps to use the Scotts spreader: Prepare, Fill, Set, and Go.
EdgeGuard Technology
The Scotts EdgeGuard Technology allows you to block off the right-side spreader pattern, preventing product from spreading onto non-lawn areas. To activate, slide the lever to the 'ON' position. This creates a controlled 3-foot spread on the left side, while the 'OFF' position allows for a full 5-foot broadcast spread.
Image: Diagram showing EdgeGuard ON (3' controlled spread) and EdgeGuard OFF (5' broadcast spread) to protect landscapes and driveways.
Usage Demonstration Videos
Video: A user demonstrates the application of lawn care products using the Scotts Turf Builder Spreader, highlighting its ease of use.
Video: This video showcases the features and benefits of the Scotts seed spreader during actual lawn application.
Maintenance
To ensure the longevity and optimal performance of your Scotts Turf Builder EdgeGuard DLX Broadcast Spreader, regular maintenance is recommended:
- After each use, empty any remaining product from the hopper.
- Rinse the hopper and spreader mechanism thoroughly with water to remove all residue.
- Allow the spreader to air dry completely before storing to prevent rust and corrosion.
- Periodically check all moving parts, including the wheels, agitator, and control cables, for any signs of wear or damage.
- Lubricate moving parts as needed with a silicone-based lubricant to maintain smooth operation.
Troubleshooting
If you encounter issues with your Scotts Turf Builder EdgeGuard DLX Broadcast Spreader, refer to the following common troubleshooting tips:
- Uneven Spreading: Ensure the spreader setting matches the product's recommendation. Check the agitator for clogs or obstructions. Verify that the wheels are turning freely and consistently.
- Product Not Dispensing: Confirm that the flow control lever is fully open. Check for any clogs in the hopper or dispensing mechanism. Ensure the agitator is spinning correctly when the wheels turn.
- EdgeGuard Malfunction: Inspect the EdgeGuard mechanism for any debris or damage that might prevent it from engaging or disengaging properly. Ensure the control cable is securely attached and not frayed.
- Difficulty Pushing: Check the wheels for debris buildup, especially grass or mud, that might impede their rotation. Ensure the axle is clear and lubricated.
For persistent issues, contact Scotts customer support for further assistance.
Specifications
| Attribute | Detail |
|---|---|
| Brand | Scotts |
| Model Name | EdgeGuard DLX Broadcast Spreader |
| Color | Green |
| Material | Grass (referring to application type, likely plastic/metal construction) |
| Item Dimensions (L x W x H) | 19 x 22 x 22 inches |
| Item Weight | 10.9 Pounds |
| Capacity | Holds up to 15,000 sq. ft. of product |
| UPC | 032247762328 |
| Manufacturer | The Scotts Company LLC |
Warranty and Support
For warranty information, product registration, or further support, please refer to the documentation included with your Scotts Turf Builder EdgeGuard DLX Broadcast Spreader or visit the official Scotts website. Customer service contact details can typically be found on the product packaging or the manufacturer's website.