Tamiya TS-41 Coral Blue Spray Lacquer Instruction Manual

1. Introduction

This manual provides essential instructions for the safe and effective use of Tamiya TS-41 Coral Blue Spray Lacquer. This product is a synthetic lacquer spray paint designed for model construction and other hobby applications. It is suitable for use on ABS and Styrene plastics, and can also be applied to metal parts. Please read all instructions carefully before use.

2. Safety Information

WARNING: FLAMMABLE LIQUID AND VAPOR. KEEP OUT OF REACH OF CHILDREN.

• Ventilation: Use only in a well-ventilated area. Avoid breathing vapors. If using indoors, ensure adequate air circulation or use a respirator.
• Ignition Sources: Keep away from heat, hot surfaces, sparks, open flames, and other ignition sources. No smoking.
• Eye and Skin Protection: Wear appropriate eye protection (safety glasses) and protective gloves to prevent contact with skin and eyes.
• Ingestion: Do not ingest. If swallowed, seek immediate medical attention.
• Pressure Container: Pressurized container: May burst if heated. Do not pierce or burn, even after use.
• Storage: Store in a cool, dry place, away from direct sunlight and temperatures above 50°C (122°F).
• Disposal: Dispose of contents/container in accordance with local regulations.

Image: Safety symbols indicating flammability, irritant, and corrosive properties, alongside the TS-41 color swatch. Always observe safety precautions when handling this product.

3. Product Overview

Tamiya TS-41 Coral Blue is a high-quality spray lacquer providing a smooth, gloss finish. It is formulated for excellent adhesion and durability on various model surfaces.

Image: A Tamiya Color spray paint can, TS-41 Coral Blue, highlighting its intended use for plastics and adult modelers.

• Color: Coral Blue (TS-41)
• Finish: Gloss
• Volume: 100ml (3.3 fl oz)
• Recommended Surfaces: ABS plastic, Styrene plastic, Metal
• Indoor/Outdoor Usage: Indoor (with proper ventilation)

4. Setup and Preparation

1. Surface Cleaning: Ensure the surface to be painted is clean, dry, and free of dust, grease, oil, and fingerprints. Use a suitable degreaser or mild soap and water, then rinse thoroughly and allow to dry completely.
2. Sanding (Optional): For optimal adhesion and a smoother finish, lightly sand the surface with fine-grit sandpaper (e.g., 600-800 grit) and clean again.
3. Masking: Mask off any areas not intended for painting using painter's tape or masking fluid.
4. Shake Can: Shake the spray can vigorously for at least one minute after the mixing ball begins to rattle. This ensures proper mixing of the paint components.
5. Test Spray: Always perform a test spray on a scrap piece of material or an inconspicuous area to check color, flow, and compatibility.

5. Operating Instructions (Application)

1. Environment: Ensure the painting environment is well-ventilated and free from excessive dust. Ideal temperature for application is between 20-25°C (68-77°F) with moderate humidity.
2. Distance: Hold the can approximately 25-30 cm (10-12 inches) from the surface.
3. Application Technique: Apply paint in thin, even coats using a steady, sweeping motion. Overlap each pass slightly to ensure uniform coverage. Avoid applying thick coats, as this can lead to runs or an uneven finish.
4. Multiple Coats: Allow each coat to dry for approximately 10-15 minutes (tack-free) before applying the next. For full hardness, allow 2 hours dry time. Multiple thin coats are superior to one thick coat.
5. Curing Time: The paint will be touch-dry in a short period, but full curing can take 24-48 hours, depending on environmental conditions. Handle painted parts carefully during this time.

6. Maintenance

• Nozzle Cleaning: After each use, invert the can and spray for a few seconds until only clear propellant comes out. This prevents the nozzle from clogging. Wipe the nozzle clean with a cloth.
• Storage: Store the can upright in a cool, dry, well-ventilated area, away from direct sunlight and extreme temperatures. Ensure the cap is securely placed.

7. Troubleshooting

• Clogged Nozzle: If the nozzle clogs, remove it and soak it in lacquer thinner or mineral spirits. Clear the opening with a thin wire if necessary. Do not use a pin or sharp object to clear the nozzle while it is on the can.
• Uneven Finish/Orange Peel: This can be caused by spraying too far from the surface, insufficient shaking, or applying too thin a coat. Ensure proper distance, shake well, and apply even coats.
• Runs/Drips: Caused by applying too much paint in one area or holding the can too close. Apply thinner coats and maintain the recommended spraying distance.
• Poor Adhesion: Ensure the surface is thoroughly cleaned and prepared. Light sanding can improve adhesion on smooth surfaces.

8. Specifications

9. Warranty and Support

For information regarding product warranty or technical support, please refer to the official Tamiya website or contact your local Tamiya distributor. Keep your purchase receipt as proof of purchase.

Tamiya America, Inc.
Website: www.tamiyausa.com (Example link, actual link may vary)