EUFAB APA 16540 Power Pack with Compressor and Jump Starter 12V - Instruction Manual

Introduction

Thank you for choosing the EUFAB APA 16540 Power Pack. This versatile device combines a 12V jump starter, an air compressor, and a portable 12V power source, making it an essential tool for automotive, camping, and marine applications. This manual provides important information for the safe and efficient operation, maintenance, and troubleshooting of your device. Please read these instructions carefully before first use and keep them for future reference.

Safety Instructions

WARNING: Failure to follow these safety instructions may result in electric shock, fire, and/or serious injury.

• Always wear eye protection and protective gloves when working with batteries.
• Do not smoke or allow sparks or flames in the vicinity of the battery or power pack. Batteries generate explosive gases.
• Ensure proper ventilation when charging or using the jump starter.
• Keep the device away from children and unauthorized persons.
• Do not expose the power pack to rain or wet conditions.
• Never short-circuit the jump starter clamps.
• If battery acid comes into contact with skin or eyes, flush immediately with plenty of clean water and seek medical attention.
• Do not attempt to jump-start a frozen battery.
• Ensure the vehicle's ignition is off before connecting the jump starter.
• Do not use the compressor for more than 10 minutes continuously to prevent overheating. Allow it to cool down before further use.

Product Overview

The EUFAB APA 16540 Power Pack is designed for portability and multi-functionality. It features a robust casing with an integrated carrying handle, making it easy to transport.

Figure 1: Front view of the EUFAB APA 16540 Power Pack, showing the integrated compressor with pressure gauge and the main power switch.

Components:

• Jump Start Cables: Red (+) and Black (-) clamps for vehicle battery connection.
• Air Compressor: Integrated compressor with a hose and various adapters for inflation.
• Pressure Gauge: Displays current air pressure during inflation.
• 12V DC Socket: For powering 12V accessories.
• LED Work Light: Provides illumination in low-light conditions.
• Battery Level Indicator: LEDs to show the charge status of the internal battery.
• Charging Ports: Input for 230V AC adapter and 12V DC car charger.
• Integrated Carrying Handle: For easy transport.

Figure 2: Top view of the Power Pack, highlighting the ON/OFF switch, LED work light, and battery level indicators.

Setup and Initial Charging

Before first use, fully charge the EUFAB APA 16540 Power Pack for at least 12-15 hours. Regular charging is crucial for maintaining battery life and performance.

Charging the Power Pack:

1. Using the 230V AC Adapter:
   • Connect the 230V AC adapter to the charging port on the power pack.
   • Plug the adapter into a standard wall outlet.
   • The charging indicator LED will illuminate (typically red during charging, turning green when fully charged).
   • Charge until the indicator shows full charge.
2. Using the 12V DC Car Charger:
   • Connect the 12V DC car charger to the charging port on the power pack.
   • Plug the other end into your vehicle's 12V cigarette lighter socket.
   • The charging indicator LED will illuminate.
   • Charge until the indicator shows full charge.

It is recommended to recharge the power pack every 2-3 months, even when not in use, to ensure optimal battery health.

Operation

1. Jump Starting a Vehicle

Use this function to start vehicles with a discharged 12V battery.

1. Ensure the vehicle's ignition is OFF and all accessories (lights, radio, etc.) are turned off.
2. Connect the red (+) jump start clamp to the positive (+) terminal of the vehicle's discharged battery.
3. Connect the black (-) jump start clamp to a clean, unpainted metal part of the vehicle's chassis, away from the battery and fuel lines. Do NOT connect to the negative (-) battery terminal directly.
4. Ensure all connections are secure.
5. Turn on the power pack's jump start function (if applicable, refer to specific switch on your model).
6. Attempt to start the vehicle. If it doesn't start after 5-6 seconds, wait at least 3 minutes before trying again.
7. Once the vehicle starts, immediately disconnect the black (-) clamp from the chassis, then disconnect the red (+) clamp from the battery.
8. Turn off the power pack.

Figure 3: The Power Pack connected to a vehicle's battery terminals for jump-starting. Note the correct connection order for safety.

2. Using the Air Compressor

The integrated compressor can inflate tires, sports equipment, and other inflatables.

1. Ensure the power pack is adequately charged.
2. Screw the compressor hose adapter onto the valve stem of the item to be inflated. For different items (e.g., bicycle tires, inflatable mattresses), use the appropriate adapter provided.
3. Check the pressure gauge for the current pressure.
4. Turn on the compressor switch.
5. Monitor the pressure gauge closely. Once the desired pressure is reached, turn off the compressor switch.
6. Unscrew the hose adapter from the valve stem.

Important: Do not over-inflate. Refer to the manufacturer's recommended pressure for the item you are inflating. Do not operate the compressor for more than 10 minutes continuously. Allow a cooling period of at least 15 minutes between uses.

Figure 4: The Power Pack's compressor in use, inflating a car tire. The pressure gauge is visible for monitoring.

3. Using the 12V DC Power Socket

The 12V DC socket can power various 12V accessories (e.g., car vacuum cleaners, portable coolers) up to a maximum current draw.

1. Ensure the power pack is adequately charged.
2. Plug your 12V accessory into the 12V DC socket on the power pack.
3. Turn on the power pack's 12V output switch (if available).
4. When finished, turn off the output switch and unplug the accessory.

Note: The 12V socket is protected by an internal fuse. If an accessory does not work, check the accessory's power requirements and the power pack's charge level.

4. Using the LED Work Light

The integrated LED light provides convenient illumination.

• Locate the switch for the LED light (refer to Figure 2).
• Toggle the switch to turn the light ON or OFF.

Maintenance

Battery Care:

• Recharge the power pack immediately after each use.
• If not in frequent use, recharge the power pack every 2-3 months to prevent deep discharge and prolong battery life.
• Do not store the power pack in extreme temperatures (hot or cold).

Cleaning:

• Wipe the exterior of the power pack with a soft, damp cloth.
• Do not use harsh chemicals or abrasive cleaners.
• Ensure all ports and openings are free from dust and debris.

Storage:

• Store the power pack in a cool, dry place, away from direct sunlight and moisture.
• Keep the jump start clamps clean and free of corrosion.

Troubleshooting

Specifications

• Model: APA 16540
• Battery Type: Lead Acid
• Battery Voltage: 12 V
• Battery Capacity: 7 Ah (7000 mAh) / 10 Ah (10000 mAh) - Note: Discrepancy in source data, using both for clarity.
• Jump Start Current: 250 A (max. 500 A)
• Compressor Pressure: 18 bar (260 PSI)
• 12V DC Socket Output: 1 x 12 V
• Charging Input: 230V AC adapter or 12V DC car charger
• Dimensions (L x W x H): Approximately 25.5 x 23 x 16.5 cm (10 x 9 x 6.5 inches)
• Weight: Approximately 3.8 kg (8.38 lbs)
• Special Features: LED Light, Portable
• Certifications: CE

Warranty and Support

The EUFAB APA 16540 Power Pack is designed for durability and performance. Spare parts availability is typically 1 year from the date of purchase.

For technical support, warranty claims, or questions not covered in this manual, please contact your retailer or the manufacturer's customer service. Keep your proof of purchase for warranty purposes.

Manufacturer: APA

Brand: EUFAB