Introduction
The CDN Dual Sensing Programmable Probe Thermometer and Timer (Model DSP1) is designed to accurately measure both the internal temperature of food and the ambient temperature of your oven or grill. This versatile tool assists in achieving precise cooking results and ensuring food safety. It features a durable stainless steel probe and cable, a clear digital display, and programmable alarms.
Image: Front view of the CDN DSP1 thermometer with probe attached, displaying oven and food temperatures.
Key Features
- Dual Sensing Probe: Measures both food and oven/grill temperatures simultaneously.
- Wide Temperature Range: 32 to 572°F (0 to 300°C).
- Programmable Alarms: Set desired temperatures for food and oven; an alarm sounds when reached.
- Timer Function: Includes a 10-hour count up/down timer.
- Durable Construction: 6.75-inch (17 cm) stainless steel probe with a 39-inch (1 m) sensor cable.
- Versatile Mounting: Features a magnet for metal surfaces and a fold-out stand for countertops.
- Unit Selection: Easily switch between Fahrenheit and Celsius.
- Power: Operates on 1 AAA battery (included).
Setup
- Battery Installation:
Locate the battery compartment on the back of the unit. Insert one AAA battery, ensuring correct polarity. The display will activate.
- Probe Connection:
Insert the stainless steel probe's jack firmly into the port on the side of the thermometer unit.
Image: The CDN DSP1 thermometer with its probe securely plugged into the side port.
- Placement:
Position the thermometer unit using either the magnetic back to attach it to a metal surface (e.g., oven door, refrigerator) or extend the fold-out stand for countertop use.
Image: Rear view of the CDN DSP1 thermometer, highlighting the integrated magnet and the fold-out stand for versatile placement.
Operating Instructions
Temperature Measurement
- Insert Probe: Carefully insert the tip of the probe into the thickest part of the food, avoiding bone or gristle. For oven temperature, position the probe tip within the oven cavity, ensuring the cable is not pinched.
- Power On: Press the ON/OFF button to activate the thermometer.
- Select Unit: Press the °F/°C button to toggle between Fahrenheit and Celsius display.
- Set Food Temperature Alarm:
- Press the MODE button until "FOOD" is selected.
- Press the MEAT button to cycle through pre-programmed meat types (e.g., Beef, Pork, Chicken) or press SET to manually adjust the target temperature using the HR and MIN buttons.
- Press ALERT ON/OFF to activate the alarm. The alarm will sound when the food reaches the set temperature.
- Set Oven Temperature Alarm:
- Press the MODE button until "OVEN" is selected.
- Press SET to manually adjust the target oven temperature using the HR and MIN buttons.
- Press ALERT ON/OFF to activate the alarm. The alarm will sound when the oven reaches the set temperature.
Timer Function
- Select Timer Mode: Press the MODE button until "TIMER" is selected.
- Set Time: Use the HR and MIN buttons to set the desired countdown time (up to 10 hours).
- Start/Stop: Press the START/STOP button to begin or pause the countdown.
- Reset: To clear the timer, press and hold the START/STOP button.
Maintenance
- Cleaning the Probe: After each use, wipe the stainless steel probe with a damp cloth and mild detergent. Rinse thoroughly and dry completely. Do not immerse the probe cable connector or the main unit in water.
- Cleaning the Unit: Wipe the thermometer unit with a soft, damp cloth. Do not use abrasive cleaners or immerse the unit in water.
- Storage: Store the thermometer and probe in a clean, dry place when not in use. Ensure the probe cable is not kinked or damaged.
- Battery Replacement: Replace the AAA battery when the display becomes dim or unresponsive.
Image: The CDN DSP1 thermometer and its probe laid out on a wooden cutting board, ready for use or cleaning.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No display or dim display | Low or dead battery; incorrect battery installation. | Replace the AAA battery, ensuring correct polarity. |
| Inaccurate temperature readings | Probe not fully inserted; probe or cable damage; probe tip touching bone/gristle. | Ensure probe is fully inserted into the thickest part of the food. Avoid bone. Inspect probe and cable for damage. If damaged, replace the probe. |
| Alarm not sounding | Alarm function not activated; volume too low. | Press the ALERT ON/OFF button to activate. Check for any volume settings (if applicable, though this model typically has a fixed alarm). |
| Probe not registering temperature | Probe not properly connected to the unit. | Ensure the probe jack is firmly seated in the port. |
Specifications
- Model: DSP1
- Temperature Range: 32 to 572°F (0 to 300°C)
- Probe Length: 6.75 inches (17 cm)
- Cable Length: 39 inches (1 m)
- Power Source: 1 x AAA battery (included)
- Display Type: Digital LCD
- Materials: Acrylonitrile Butadiene Styrene (ABS) casing, Stainless Steel probe and cable
- Features: Dual sensing, programmable alarms, timer, magnet/stand mounting
- Dimensions (Unit): Approximately 7.5 inches (H) x 3 inches (W) x 0.625 inches (D)
Image: The CDN DSP1 thermometer with key dimensions indicated, showing its compact size.
Warranty Information
CDN products are manufactured with quality materials and craftsmanship. For specific warranty details and terms, please refer to the documentation included with your product or visit the official CDN website. Keep your purchase receipt as proof of purchase for any warranty claims.
Support
For further assistance, product inquiries, or technical support, please contact CDN customer service. Contact information can typically be found on the product packaging or the official CDN website.
Manufacturer: CDN
Website: www.cdn-timeandtemp.com
Phone: 800-338-5594
