Lee Precision 90886 Pro 1000 Load-Master Bullet Feeder Die & Fingers Instruction Manual

1. Product Overview

The Lee Precision 90886 kit is designed to convert or adapt your existing Lee bullet feed system on a Pro 1000 Load-Master progressive press for different calibers or bullet lengths. This kit allows reloaders to easily change out the bullet feed die and fingers to accommodate bullets with a diameter between 9mm (.355) and .365 inches, and up to .46 inches long. It is an essential component for optimizing your reloading setup for specific bullet types.

2. Components Included

The Lee Precision 90886 kit includes the following items:

• Feed Die #2 (for 9mm to .365 caliber bullets)
• Small Feed Fingers (designed for bullets up to .46 inches long)

3. Setup and Installation

This kit is intended for use with the Lee Pro 1000 Load-Master progressive press. Proper installation requires familiarity with your reloading press and its existing bullet feed system.

1. Safety First: Ensure your reloading press is clear of primers, powder, and bullets before beginning installation. Always wear appropriate safety glasses.
2. Remove Existing Components: Carefully remove the existing bullet feed die and feed fingers from your Lee Pro 1000 Load-Master press, if applicable. Refer to your main press instruction manual for specific removal procedures.
3. Install New Feed Die: Thread the new bullet feed die (#2) into the designated station on your press. Adjust its height according to the bullet length you will be using. The die should be set so that it properly seats the bullet into the case mouth without deforming it.
4. Attach Small Feed Fingers: Secure the small feed fingers to the bullet feeder mechanism. Ensure they are correctly aligned to receive and guide bullets into the feed die.
5. Initial Adjustment: Perform initial adjustments with dummy rounds (cases without primer or powder) to ensure smooth feeding and proper bullet seating. Fine-tune the die height and finger alignment as needed.

For detailed instructions on integrating bullet feed systems with your specific Lee Pro 1000 Load-Master press, consult the comprehensive manual provided with your press.

4. Operation

Once the bullet feed die and fingers are correctly installed and adjusted, the system will automatically feed bullets into the cases as the press operates.

• Ensure the bullet feeder hopper is adequately filled with the correct caliber and length bullets.
• Operate the press smoothly and consistently. The feed fingers will pick up a bullet and present it to the feed die, which then guides it into the case.
• Periodically check the bullet seating depth and overall cartridge length to maintain consistency and safety.

5. Maintenance

Regular maintenance ensures the longevity and reliable performance of your bullet feeder components.

• Cleaning: After each reloading session, clean the bullet feed die and fingers to remove any bullet lube residue, dust, or debris. A soft cloth and a mild solvent (if necessary) can be used. Ensure all components are dry before reassembly or storage.
• Inspection: Periodically inspect the feed fingers for wear or damage. Worn fingers can lead to inconsistent bullet feeding. Replace any damaged components immediately.
• Storage: Store the components in a clean, dry environment when not in use to prevent corrosion or damage.

6. Troubleshooting

If you encounter issues with your bullet feeder system, consider the following:

• Bullets Not Feeding:
  • Check if the bullet feeder hopper is empty or jammed.
  • Verify that the bullet feed die is correctly adjusted for the bullet length.
  • Inspect the feed fingers for proper alignment and wear.
  • Ensure the bullets are within the specified diameter and length range for this kit.
• Inconsistent Bullet Seating:
  • Re-check the bullet feed die height adjustment.
  • Ensure the cases are properly flared to accept the bullet.
  • Inspect the bullets for deformities or inconsistencies.
• Bullet Tipping or Falling:
  • Ensure the small feed fingers are securely attached and not damaged.
  • Verify the bullet feed die is aligned correctly with the case.

For further assistance, refer to your Lee Pro 1000 Load-Master press manual or contact Lee Precision customer support.

7. Specifications

8. Safety Information and Legal Disclaimer

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Always handle reloading components in a well-ventilated area and wash hands thoroughly after use.

Reloading can be dangerous if not performed correctly. Always follow all safety guidelines provided with your reloading press and components. Keep out of reach of children.

9. Warranty and Support

For information regarding product warranty, replacement parts, or technical support, please contact Lee Precision directly. Their official website typically provides detailed contact information and support resources.

Visit Lee Precision Support