Progress Lighting P745-IC
Progress Lighting P745-IC Recessed-Housing Instruction Manual
Model: P745-IC | Brand: Progress Lighting
1. Introduction
This manual provides detailed instructions for the safe installation, operation, and maintenance of your Progress Lighting P745-IC Recessed-Housing. This incandescent housing is designed for sloped ceilings and features an adjustable lamp angle from 9 to 45 degrees. It is suitable for both new construction and remodel applications.
Please read these instructions thoroughly before beginning installation to ensure proper function and safety.
2. Important Safety Information
WARNING: Risk of Fire or Electric Shock.
- Always disconnect power at the circuit breaker before installation or servicing.
- All wiring connections must be in accordance with local and national electrical codes. If you are unsure about wiring, consult a qualified electrician.
- Do not install in locations where the operating temperature exceeds the fixture's rated temperature.
- Ensure the fixture is properly grounded.
- This product is UL and CUL listed for damp locations and through wiring.
- Use only incandescent lamps with a maximum wattage of 75 watts.
3. Setup and Installation
The P745-IC housing is designed for easy installation in ceilings ranging from 1/2-inch to 1-1/2-inch thick. Integral locking clips facilitate quick and secure installation.
3.1 Tools Required
- Screwdriver (Phillips and Flathead)
- Wire Strippers
- Pliers
- Measuring Tape
- Drywall Saw or Hole Saw (for new openings)
- Safety Glasses
3.2 Installation Steps
- Prepare the Opening: For remodel applications, ensure the existing ceiling opening is approximately 7 inches in diameter. For new installations, cut a circular opening of approximately 7 inches in the ceiling.
- Connect Wiring: Open the junction box cover on the housing. Connect the building's electrical supply wires to the fixture's wires according to local electrical codes. The housing is rated for 4 #12 90-degree conductors (2 in and 2 out). Ensure all connections are secure using appropriate wire connectors. Close the junction box cover.
- Insert Housing: Carefully insert the recessed housing into the ceiling opening. The integral locking clips will engage with the ceiling material, securing the housing in place.
- Adjust Lamp Angle: The housing allows for lamp adjustment from 9 to 45 degrees to accommodate various sloped ceiling angles. Adjust the internal mechanism to achieve the desired light direction.
- Install Trim (Sold Separately): Once the housing is securely installed, attach the compatible trim (not included) to complete the fixture. The integral white cast trim flange ring provides for secure installation of the trim.
Figure 3.2.1: Overview of the Progress Lighting P745-IC Recessed Housing. This image shows the main components including the junction box, flexible conduit, and the cylindrical housing with its adjustable interior.
Figure 3.2.2: Dimensions of the P745-IC Recessed Housing. The housing measures approximately 8-1/4 inches in width, 7-1/4 inches in height, and has an overall length of 19 inches from the junction box to the end of the housing.
4. Operating Instructions
Once installed and wired, the Progress Lighting P745-IC Recessed-Housing operates by simply turning on the connected light switch. Ensure a compatible medium base incandescent lamp (up to 75 watts) is installed in the socket before operation.
The fixture is designed for continuous use within its specified electrical ratings.
5. Maintenance
The P745-IC Recessed-Housing requires minimal maintenance. Regular cleaning and inspection are recommended to ensure optimal performance and safety.
- Cleaning: Before cleaning, ensure power is disconnected at the circuit breaker. Wipe the exterior surfaces of the trim (not the housing itself, which is concealed) with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Lamp Replacement: Disconnect power before replacing the lamp. Allow the lamp to cool completely before handling. Replace with a medium base incandescent lamp of the same type and wattage (max 75W).
- Inspection: Periodically inspect the fixture for any signs of damage, loose connections, or wear. If any issues are found, disconnect power and consult a qualified electrician.
6. Troubleshooting
If you experience issues with your recessed housing, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to fixture, loose wiring, faulty bulb, tripped circuit breaker. | Check circuit breaker. Ensure all wiring connections are secure. Replace bulb. |
| Light flickers. | Loose bulb, incorrect bulb type, loose wiring connection. | Tighten bulb. Ensure correct bulb type and wattage. Check wiring connections. |
| Fixture overheats. | Incorrect bulb wattage (too high), insufficient ventilation. | Ensure bulb wattage does not exceed 75W. Verify proper insulation clearance around housing. |
If the problem persists after trying these solutions, contact a qualified electrician or customer support.
7. Specifications
| Feature | Detail |
|---|---|
| Model Number | P745-IC |
| Brand | Progress Lighting |
| Dimensions | 8-1/4-Inch Width x 7-1/4-Inch Height (Approx. 7-Inch ceiling opening) |
| Material | Galvanized Steel |
| Light Source Type | Incandescent |
| Max Wattage | 75 watts |
| Voltage | 120 Volts |
| Lamp Adjustment | 9 to 45 degrees |
| Ceiling Thickness Compatibility | 1/2-Inch to 1-1/2-Inch |
| Certifications | UL and CUL listed for damp locations and through wiring |
| Item Weight | 3 Pounds |
8. Warranty and Support
Warranty: Your Progress Lighting P745-IC Recessed-Housing comes with a 1-year Limited Warranty. This warranty guarantees your complete satisfaction with your purchase and includes professional after-sales customer service support.
For further assistance, technical support, or warranty claims, please visit the official Progress Lighting store or contact their customer service department.
Related documentsP745-IC
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.