1. Introduction
This instruction manual provides essential information for the safe and effective use of your Bosch 2607000102 Parallel Guide. Please read this manual thoroughly before installation and operation. Keep it for future reference.
2. Safety Information
Always observe general safety precautions when working with power tools and accessories. This parallel guide is designed to enhance precision when planing; however, improper use can still lead to injury or damage.
- Ensure the parallel guide is securely attached to the planer before operation.
- Always wear appropriate personal protective equipment, including safety glasses and hearing protection.
- Disconnect the planer from the power source before attaching or adjusting the parallel guide.
- Keep hands and fingers away from the cutting area during operation.
- Use the parallel guide only with compatible Bosch planers as specified in this manual.
3. Product Overview
The Bosch 2607000102 Parallel Guide is an accessory designed to assist in making straight, parallel cuts with compatible Bosch planers. It provides a stable reference edge for consistent planing depth and width.
Image 1: The Bosch 2607000102 Parallel Guide shown on a workbench, ready for use with a planer. Safety glasses are visible in the foreground.
3.1. Package Contents
- 1 x Bosch 2607000102 Parallel Guide
3.2. Compatible Planers
This parallel guide is compatible with the following Bosch planer models:
- PHO 16-82
- PHO 25-82
- PHO 35-82C
- PHO 100
- PHO 15-82
- GHO 26-82
- GHO 31-82
- GHO 36-82C
- GHO 14,4 V
4. Installation and Setup
Follow these steps to properly attach the parallel guide to your Bosch planer:
- Ensure Power is Disconnected: Before beginning, always unplug your planer from the power source to prevent accidental startup.
- Locate Mounting Points: Identify the designated mounting slots or holes on the side of your planer's base plate. Refer to your planer's instruction manual for specific details.
- Attach the Guide: Slide the parallel guide's rods or mounting bracket into the planer's mounting points.
- Secure the Guide: Use the provided fasteners (typically a knob or screw) to firmly secure the parallel guide to the planer. Ensure there is no wobble.
- Adjust for Width: Loosen the adjustment knob on the parallel guide and slide the fence to the desired planing width. Tighten the knob securely once the desired width is set.
Image 2: A close-up view of the Bosch Parallel Guide, highlighting the adjustment knob and the slots for attaching it to a planer.
5. Operation
Once the parallel guide is securely attached and adjusted, you can begin planing. The guide helps maintain a consistent distance from the edge of your workpiece.
- Set Planing Depth: Adjust the planing depth on your planer according to your project requirements.
- Position Workpiece: Place your workpiece on a stable surface.
- Align Guide: Position the planer so that the parallel guide's fence rests firmly against the edge of your workpiece.
- Start Planer: Turn on the planer and allow it to reach full speed before engaging the workpiece.
- Guide the Planer: Apply steady, even pressure and guide the planer along the edge of the workpiece, keeping the parallel guide's fence in constant contact with the edge.
- Complete Pass: Continue until the entire length of the desired cut is planed. Repeat for additional passes if necessary, readjusting depth as needed.
6. Maintenance and Care
Proper maintenance ensures the longevity and performance of your parallel guide.
- Cleaning: After each use, wipe down the parallel guide with a clean, dry cloth to remove dust and debris. Avoid using harsh chemicals that could damage the finish.
- Inspection: Periodically inspect the guide for any signs of damage, bending, or loose fasteners. Replace or tighten components as needed.
- Storage: Store the parallel guide in a dry, clean environment, away from extreme temperatures and moisture, to prevent corrosion.
7. Troubleshooting
If you encounter issues while using the parallel guide, consider the following:
- Inaccurate Cuts: Ensure the parallel guide is securely fastened to the planer and the adjustment knob is tightened. Verify that the guide's fence is consistently pressed against the workpiece edge during operation.
- Difficulty Attaching: Confirm that your planer model is listed as compatible. Check for any obstructions in the mounting slots or on the guide itself.
- Wobbling: Tighten all fasteners. If wobbling persists, inspect the guide and planer's mounting points for wear or damage.
For persistent issues, consult your planer's instruction manual or contact Bosch customer support.
8. Technical Specifications
| Specification | Detail |
|---|---|
| Model Number | 2607000102 |
| Brand | Bosch |
| Material | Metal |
| Colour | Silver |
| Product Dimensions (L x W x H) | 16.7L x 13.7W x 4.1H centimetres |
| Item Weight | 0.38 kg |
| Manufacturer Part Number | 2607000102 |
| Global Trade Identification Number (GTIN) | 03165140013383 |
Image 3: A diagram illustrating the dimensions of the Bosch Parallel Guide.
9. Warranty and Support
For information regarding warranty coverage, service, or technical support for your Bosch 2607000102 Parallel Guide, please refer to the documentation included with your original Bosch planer or visit the official Bosch Tools website. You may also contact Bosch customer service directly for assistance.
Bosch Tools Website: www.bosch-pt.com
