Introduction
This manual provides instructions for the assembly, operation, maintenance, and troubleshooting of your Alpine Corporation 35" Tall 3-Tier Outdoor Pedestal Water Fountain. This durable resin plastic fountain is designed to enhance your outdoor space with the soothing sound of cascading water and can also serve as a birdbath.
Image: The Alpine Corporation 3-Tier Pedestal Water Fountain positioned in a lush garden, showcasing its elegant design and water flow.
Setup Instructions
1. Unpacking and Inspection
- Carefully remove all components from the packaging.
- Inspect all parts for any damage. Contact customer support if any parts are missing or damaged.
- Ensure all included components are present: fountain tiers, pedestal, base, pump, and power cord.
2. Assembly
Follow these steps to assemble your fountain:
- Attach the pedestal to the base by screwing them together securely.
- Place the pump inside the lowest basin of the fountain. Ensure the pump's tubing is correctly connected to the water outlet.
- Stack the fountain tiers, ensuring they are properly aligned and the water flows correctly from one tier to the next.
- Route the power cord safely to an outdoor-rated electrical outlet.
Image: An image showing the individual components of the fountain, including the base, pedestal, and tiered basins, ready for assembly.
3. Placement
- Choose a level surface for the fountain to ensure even water flow and stability.
- Position the fountain near an appropriate outdoor power source.
4. Initial Water Fill
- Fill the lowest basin with distilled water until the pump is fully submerged. Do not overfill.
- Plug in the power cord to activate the pump and begin water circulation.
Video: A detailed guide on the key features and assembly process of the Alpine Water Fountain.
Operating Instructions
1. Powering On/Off
- To turn on the fountain, plug the power cord into a suitable outdoor electrical outlet.
- To turn off the fountain, unplug the power cord from the electrical outlet.
2. Water Level Maintenance
- Regularly check the water level in the lowest basin. Evaporation will occur, especially in warm or windy conditions.
- Refill with distilled water as needed to ensure the pump remains fully submerged. Operating the pump without sufficient water can cause damage.
Image: A close-up view of water gently flowing over the textured tiers of the fountain, highlighting the cascading effect.
Video: A short demonstration of the fountain in operation, showcasing its water flow.
Maintenance
1. Regular Cleaning
- Clean the fountain at least once a week to prevent algae buildup and mineral deposits.
- Unplug the fountain before cleaning. Drain the water and wipe down all surfaces with a soft cloth and mild soap. Rinse thoroughly.
2. Pump Maintenance
- The pump may need cleaning every few weeks, especially if debris or sediment accumulates.
- Disconnect the pump from the power source. Remove the pump from the fountain and disassemble it according to the pump's specific instructions (usually involves removing the cover and impeller).
- Clean the impeller and pump housing with a small brush and clean water. Reassemble the pump and place it back in the fountain.
3. Winterization
- In regions with freezing temperatures, drain all water from the fountain before winter.
- Clean the fountain and pump thoroughly. Store the pump indoors in a dry, frost-free location.
- Cover the fountain or store it indoors to protect it from harsh winter conditions.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water not flowing | Pump not plugged in; insufficient water level; clogged pump/tubing. | Ensure power cord is plugged in; add water until pump is submerged; clean pump and tubing. |
| Uneven water flow | Fountain not level; debris in water outlets. | Adjust fountain placement to a level surface; clear any blockages from water outlets. |
| Excessive splashing | Water flow too strong; fountain not level. | Adjust pump's flow rate (if applicable); ensure fountain is on a level surface. |
| Water leakage | Cracked basin; loose connections. | Inspect basins for cracks; ensure all connections are tight. |
Image: A detailed view of the water flow from the fountain's tiers, which can assist in identifying uneven distribution or blockages.
Specifications
- Model Number: TEC106
- Dimensions (L x W x H): 20" x 20" x 35" (51 cm x 51 cm x 89 cm)
- Material: Durable Resin Plastic
- Color: Green
- Item Weight: 6 pounds
- Power Source: Corded Electric
- Included Components: 1 x 3-Tiered Pedestal Water Fountain and Bird Bath
Image: A visual representation of the fountain with its key dimensions (length, width, and height) indicated.
Warranty
This Alpine Corporation product is backed by a two-year support period, ensuring assistance for any manufacturing defects or operational issues within this timeframe.
Support
For further assistance, technical support, or warranty claims, please contact Alpine Corporation customer service. Our dedicated teams are available to provide fast and reliable support.
Refer to the product packaging or the official Alpine Corporation website for the most current contact information.
