Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the Elkay LK60 1-1/2" Diameter Brass Tubing and Tailpiece with Center Outlet. This product is designed to create a continuous waste drain connection for multi-bowl sinks, ensuring efficient water drainage.
Safety Information
Please read all instructions carefully before beginning installation. Failure to follow these instructions may result in property damage or personal injury. Always wear appropriate personal protective equipment, such as safety glasses and gloves, during installation.
- Ensure water supply is turned off before starting any plumbing work.
- Use only the tools specified and ensure they are in good working condition.
- Do not overtighten connections, as this can damage components.
- Check for leaks thoroughly after installation is complete.
Package Contents
Verify that all components are present before beginning installation:
- 1x Elkay LK60 Center Outlet Fitting (Chrome-plated brass)
- 2x 1-1/2" Diameter Brass Tubing with Tailpiece (Chrome-plated)
- Necessary washers and nuts for connection (typically included with plumbing components)
This image displays the primary components of the Elkay LK60 continuous waste drain connection. It includes two chrome-plated brass tubes, one with a curved end and the other with a similar curved end, designed to connect to sink drains. In the center is the chrome-plated brass cross-shaped outlet fitting, which connects the two tubes and directs water to the main drain.
Setup and Installation
This section outlines the steps for installing the Elkay LK60 continuous waste drain connection. Basic plumbing tools such as a pipe wrench, pliers, and a screwdriver may be required.
- Prepare the Sink Drains: Ensure that the sink drains are clean and free of debris. If replacing an existing drain system, remove all old components.
- Connect Tailpieces to Sink Drains: Attach the curved ends of the 1-1/2" diameter brass tubing tailpieces to the sink drain openings. Use appropriate washers and nuts to create a watertight seal. Hand-tighten first, then use a wrench for a final snug fit, being careful not to overtighten.
- Position the Center Outlet Fitting: Align the Elkay LK60 center outlet fitting between the two tailpieces. The fitting has three openings: two for the tailpieces and one for the main drain connection.
- Connect Tailpieces to Center Outlet: Insert the straight ends of the brass tubing tailpieces into the side openings of the center outlet fitting. Secure these connections with the provided nuts and washers, ensuring a tight seal.
- Connect to Main Drain: Attach the bottom opening of the center outlet fitting to your existing main drain P-trap or waste line. This connection will typically involve a slip nut and washer. Ensure all connections are properly aligned and tightened.
- Test for Leaks: Once all connections are secure, turn on the water supply and fill the sink(s). Observe all connections for any signs of leaks. If leaks are detected, gently tighten the corresponding nuts until the leak stops. Do not overtighten.
Operating
The Elkay LK60 continuous waste drain connection operates passively by directing water from multiple sink bowls into a single drain line. Once properly installed, it requires no active operation. Water will flow through the tailpieces, converge in the center outlet fitting, and then proceed to the main drain system.
Maintenance
Regular maintenance helps ensure the longevity and proper function of your Elkay LK60 drain system.
- Cleaning: Periodically clean the visible chrome surfaces with a soft cloth and a mild, non-abrasive cleaner. Avoid harsh chemicals or abrasive pads, which can damage the chrome finish.
- Inspection: Annually inspect all connections for any signs of wear, corrosion, or leaks. Check for loose nuts and tighten them if necessary.
- Clog Prevention: Avoid pouring grease, coffee grounds, or other solid waste down the drain to prevent clogs. Use a drain strainer in your sink bowls.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Leaks at connections | Loose nuts, improperly seated washers, damaged washers. | Tighten nuts gently. Disassemble, inspect, and reseat or replace washers if damaged. Ensure proper alignment. |
| Slow drainage or clog | Accumulation of debris (food particles, hair, grease) in the drain system. | Remove the P-trap and clean out any obstructions. Use a plumbing snake if the clog is further down the line. Avoid chemical drain cleaners as they can damage plumbing. |
| Corrosion or discoloration of chrome finish | Exposure to harsh chemicals, abrasive cleaning, hard water deposits. | Clean with mild soap and water. For hard water stains, use a vinegar solution. Avoid abrasive cleaners. |
Specifications
| Feature | Detail |
|---|---|
| Brand | Elkay |
| Model Number | LK60 |
| Material | Brass |
| Finish Type | Chrome |
| Tubing Diameter | 1-1/2 inches |
| Product Dimensions | Approximately 31.25 x 6.25 x 2.25 inches (L x W x H) |
| Item Weight | Approximately 1 pound |
| UPC | 094902179001 |
Warranty Information
For specific warranty details regarding the Elkay LK60 product, please refer to the official warranty documentation provided by Elkay at the time of purchase or visit the official Elkay website. Warranty terms typically cover manufacturing defects and material flaws under normal use and service.
Support
If you require further assistance with installation, troubleshooting, or have questions about your Elkay LK60 product, please contact Elkay customer service directly. You can typically find contact information on the official Elkay website or through your product retailer.
Elkay Official Website: www.elkay.com
