Permatex 80070 Silicone Spray Lubricant Instruction Manual

1. Product Overview

The Permatex 80070 Silicone Spray Lubricant is designed to electrically insulate, lubricate, and waterproof various mechanical equipment. Its high silicone formula prevents friction, binding, and squeaking by coating surfaces. It does not attract dust or dirt and is safe for use on paint, rubber, and plastic surfaces. This product also protects and renews rubber mountings, bushings, and weather stripping.

Image: Permatex 80070 Silicone Spray Lubricant aerosol can.

2. Safety Information

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65). Always read and follow all warnings and instructions on the product label before use.

• Extremely Flammable: Keep away from heat, sparks, open flames, and hot surfaces. No smoking.
• Contents Under Pressure: Do not puncture or incinerate container. Do not expose to temperatures exceeding 120°F (49°C).
• Harmful if Swallowed: If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting.
• Inhalation Hazard: Use in a well-ventilated area. Avoid breathing vapors or spray mist.
• Eye and Skin Irritant: Avoid contact with eyes and skin. In case of contact, flush thoroughly with water.
• Keep Out of Reach of Children.

3. Preparation for Use

Before applying the Permatex 80070 Silicone Spray Lubricant, ensure the area is properly prepared for optimal performance and safety.

1. Clean Surface: For best results, clean the surface or component to be lubricated, removing any existing dirt, grease, or old lubricant. A clean, dry surface allows the silicone to adhere and perform effectively.
2. Ventilation: Ensure the application area is well-ventilated to prevent inhalation of vapors.
3. Shake Can: Shake the aerosol can thoroughly for several seconds before use to ensure proper mixing of contents.
4. Protect Surrounding Areas: While the product is designed not to mar paint, rubber, or plastic, it is advisable to cover adjacent areas if overspray is a concern, especially in sensitive applications.

4. Application Instructions

Follow these steps for effective application of Permatex 80070 Silicone Spray Lubricant:

1. Aim Nozzle: Point the spray nozzle directly at the area requiring lubrication.
2. Apply Evenly: Press the actuator button and apply a light, even coat of lubricant to the desired surface. Avoid excessive application.
3. Targeted Use: This lubricant is suitable for various applications including:
   • Door locks and hinges
   • Trunk lids
   • Brake cables
   • Rubber molding, mountings, and bushings
   • Window channels
   • General mechanical equipment requiring lubrication and waterproofing
4. Allow to Dry: For electrical insulation and waterproofing, allow the product to dry completely. For lubrication, the effect is immediate.
5. Reapply as Needed: Reapply if squeaking or binding returns, or as part of routine maintenance.

The high silicone formula ensures that the lubricant does not attract dust or dirt, maintaining a clean application area. It will not mar paint, rubber, or plastic surfaces.

5. Care and Storage

Proper care and storage will ensure the longevity and effectiveness of your Permatex 80070 Silicone Spray Lubricant.

• Storage Temperature: Store in a cool, dry place, away from direct sunlight and temperatures above 120°F (49°C).
• Keep Upright: Store the can in an upright position.
• Cap Securely: Ensure the cap is securely placed on the can after each use to prevent accidental discharge and contamination.
• Disposal: Dispose of empty cans according to local regulations. Do not puncture or incinerate.

Regular application helps protect and renew rubber mountings, bushings, and weather stripping, extending their lifespan and maintaining flexibility.

6. Troubleshooting

If you encounter issues while using the Permatex 80070 Silicone Spray Lubricant, consider the following:

• Squeaking Persists: If the squeaking or binding continues after initial application, ensure the surface was clean and dry before application. Reapply a thin, even coat, ensuring the lubricant reaches all moving parts.
• Spray Pattern Issues: If the spray is inconsistent or produces too much foam, ensure the can is thoroughly shaken before use. The product is designed to spray as a foam, which can be less precise for very small areas. For pinpoint accuracy, consider alternative application methods if a straw is not available.
• Flammability Concerns: This product is flammable. If using near electrical equipment or heat sources, ensure adequate ventilation and allow sufficient time for the product to dry and vapors to dissipate before operating the equipment. Failure to do so can result in ignition of fumes.
• Product Not Dispensing: Check if the nozzle is clogged. If so, remove and clean the nozzle. Ensure the can is not empty and is stored at an appropriate temperature.

7. Product Specifications

8. Warranty and Support

For specific warranty information or technical support regarding your Permatex 80070 Silicone Spray Lubricant, please refer to the manufacturer's official website or contact their customer service department. Permatex is committed to providing quality products and assistance.

You can find more information and contact details on the official Permatex website or by visiting the Permatex Store on Amazon.