1. Introduction
This manual provides essential information for the safe assembly, operation, and maintenance of your Fire Sense 60262 Portable Tabletop Propane Patio Heater. Please read all instructions carefully before use and retain this manual for future reference.
Figure 1: Fire Sense 60262 Portable Tabletop Propane Patio Heater. This image displays the complete assembled unit, highlighting its stainless steel finish and compact design suitable for tabletop use.
2. Safety Information
WARNING: For outdoor use only. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- Always operate the heater on a firm, level surface.
- Maintain adequate clearance from combustible materials.
- Ensure proper ventilation.
- Keep children and pets away from the heater.
- Never leave the heater unattended while in operation.
- This heater is equipped with an auto shutoff tilt valve and an oxygen depletion sensor (ODS) for safety.
3. Setup and Assembly
Your Fire Sense 60262 heater requires minimal assembly. Ensure all components are present and undamaged before proceeding.
3.1 Component Identification
Refer to the packaging for a complete list of parts. Key components include the base, main pole, burner assembly, and reflector hood.
3.2 Propane Cylinder Installation
- Ensure the heater's control knob is in the 'OFF' position.
- Access the propane cylinder compartment located in the base of the heater. This typically involves unscrewing or opening a panel.
- Carefully screw a standard 1lb propane cylinder (not included) into the regulator connection. Hand-tighten only. Do not overtighten.
- Close the compartment securely.
Figure 2: Propane cylinder compartment. This image shows the internal compartment designed to hold a 1lb propane cylinder, accessible from the side of the heater's base.
Figure 3: Underside of the heater base. This view shows the sturdy base and potential mounting points for stability.
4. Operating Instructions
Follow these steps to safely ignite and operate your patio heater.
4.1 Ignition Procedure
- Ensure the propane cylinder is correctly installed and the gas supply is open.
- Locate the control knob and the Piezo igniter button on the heater's body.
- Push and turn the control knob to the 'PILOT' position. Hold it down for 30-60 seconds to purge air from the gas lines.
- While still holding the control knob down, press the Piezo igniter button repeatedly until the pilot flame ignites. You may need to listen for a click and observe the pilot light through the viewing hole.
- Once the pilot is lit, continue to hold the control knob down for another 10-15 seconds to allow the thermocouple to heat up. Release the knob slowly. If the pilot extinguishes, repeat steps 3-5.
- After the pilot is stable, turn the control knob to the desired heat setting (LOW to HIGH). The main burner will ignite.
Figure 4: Control panel. This image shows the control knob for adjusting heat and the Piezo igniter button for easy startup.
4.2 Adjusting Heat Settings
Rotate the control knob between 'LOW' and 'HIGH' to adjust the heat output according to your comfort level. The heater provides up to 10,000 BTU of heat.
Figure 5: Burner and heating grid. This close-up shows the stainless steel burner and protective grid, which glows red when operating at high heat.
4.3 Shutting Down the Heater
To turn off the heater, rotate the control knob to the 'OFF' position. Ensure the gas supply from the propane cylinder is also closed when not in use.
4.4 Official Product Video
Video 1: Fire Sense Propane Table Top Patio Heater, Stainless Steel. This video demonstrates the heater in an outdoor setting, showcasing its design and operation.
5. Maintenance
Regular maintenance ensures optimal performance and longevity of your heater.
- Cleaning: Wipe the exterior surfaces gently with a damp cloth. Do not use abrasive cleaners or solvents.
- Inspection: Periodically check the gas hose and connections for any signs of wear, damage, or leaks. Perform a leak test with soapy water if a gas odor is detected.
- Storage: When not in use, especially during off-season, disconnect the propane cylinder and store the heater in a cool, dry place, protected from weather elements.
6. Troubleshooting
If you encounter issues with your heater, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Heater will not ignite | No gas flow; Air in gas line; Faulty igniter | Check propane cylinder level and connection; Purge air by holding down control knob longer; Check igniter spark. |
| Pilot light will not stay lit | Thermocouple not heating sufficiently; Low gas pressure | Hold control knob down longer after pilot ignition; Check propane cylinder level. |
| Low flame or insufficient heat | Low gas pressure; Partially clogged burner | Check propane cylinder level; Ensure gas valve is fully open; Clean burner ports if necessary (when cool). |
| Heater shuts off unexpectedly | Tip-over switch activated; Oxygen depletion sensor activated | Ensure heater is on a stable, level surface; Check for proper ventilation. |
7. Specifications
- Model: 60262
- Brand: Fire Sense
- Heat Output: 10,000 BTU
- Fuel Type: Propane (uses standard 1lb LP gas cylinder)
- Material: Stainless Steel
- Dimensions (Assembled): 13" Base, 21" Hood, 35" H
- Weight: Approximately 17 lbs
- Safety Features: Auto Shutoff Tilt Valve, Oxygen Depletion Sensor (ODS)
- Certifications: CSA Approved
8. Warranty
This Fire Sense 60262 Portable Tabletop Propane Patio Heater comes with a 1-year limited warranty. Please retain your proof of purchase for warranty claims. For specific terms and conditions, refer to the warranty documentation included with your product or contact Fire Sense customer support.
9. Support
For further assistance, technical support, or to inquire about replacement parts, please contact Fire Sense customer service. Contact information can typically be found on the product packaging or the official Fire Sense website.
