1. Product Overview
The Permatex 80045 Pipe Joint Compound is a universal sealant designed to lubricate and seal threaded joints on various lines, including water, oil, and fuel. This compound is formulated to resist common shop fluids and remains non-hardening, allowing for easy disassembly of components when needed. It operates effectively within a temperature range of -65°F to 400°F (-54°C to 204°C).
Image 1.1: Front view of the Permatex 80045 Pipe Joint Compound 16.2 oz bottle. The label clearly displays the brand 'Permatex', product name 'Pipe Joint Compound', and model number '#80045', along with net content information.
2. Safety Information
DANGER: FLAMMABLE. MAY CAUSE ALLERGIC SKIN REACTION.
PREVENTION: Contains: Kaolin, Rosin, Ethanol, Talc, 2-propanol, Methanol, Titanium dioxide, Carbon black. Read special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves, protective clothing, eye protection, and face protection. Contaminated work clothing should not be allowed out of the workplace. Wash bare hands and any exposed skin thoroughly after handling.
Precautionary Statements – Response:
- IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower. If skin irritation or rash occurs: Get medical advice/attention. Take off contaminated clothing and wash it before reuse.
- IF INHALED: If breathing is difficult, remove victim to fresh air and keep at rest in a position comfortable for breathing.
- IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
- In case of fire: Use CO2, dry chemical, or foam for extinction.
Precautionary Statements – Storage: Store in a well-ventilated place. Keep container tightly closed.
Precautionary Statements – Disposal: Dispose of contents/container to an approved waste disposal plant in accordance with local/regional/national/international regulations.
WARNING: This product can expose you to chemicals including Carbon black, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
Image 2.1: Back view of the Permatex 80045 Pipe Joint Compound bottle, displaying detailed safety warnings, ingredients, and handling instructions in multiple languages.
3. Setup and Preparation
Proper preparation of surfaces is essential for effective sealing and to prevent leaks. Follow these steps before applying the compound:
- Clean Surfaces: Ensure that all threads and flange surfaces are thoroughly clean and free from dirt, grease, oil, or any other contaminants. Use an appropriate cleaner if necessary.
- Dry Surfaces: All surfaces must be completely dry before application to ensure proper adhesion and sealing.
4. Application Instructions
Apply the Permatex 80045 Pipe Joint Compound as follows:
- For Threaded Joints: Apply a thin, even coat of the compound to the male threads of the pipe or fitting.
- For Flanges: Apply a thin coat to each mating surface of the flange.
- Assembly: Assemble the components and tighten them as usual.
- Initial Set Time: Allow the compound to set for approximately five minutes before lightly re-tightening the connection if necessary.
- Re-tightening: The compound is non-hardening, which means connections can be re-tightened even after initial assembly without compromising the seal.
5. Maintenance and Storage
To maintain the quality and effectiveness of the Permatex 80045 Pipe Joint Compound:
- Storage: Store the container in a well-ventilated area.
- Container Integrity: Keep the container tightly closed when not in use to prevent drying or contamination.
6. Troubleshooting
If a leak occurs after application, consider the following:
- Surface Preparation: Re-check if the surfaces were clean and dry prior to application. Contaminants can prevent a proper seal.
- Application Amount: Ensure a sufficient, but not excessive, amount of compound was applied to cover all threads or flange surfaces.
- Tightening: Verify that the joint was tightened adequately. The non-hardening nature allows for re-tightening if needed.
- Temperature/Pressure: Confirm that the application conditions (temperature and pressure) are within the product's specified limits.
7. Specifications
| Specification | Detail |
|---|---|
| Product Name | Pipe Joint Compound |
| Model Number | 80045 |
| Brand | Permatex |
| Item Form | Liquid |
| Material | Silicone (Note: Product description states 'universal sealant', specifications list 'Silicone' as material. This refers to the base material properties, not necessarily 100% silicone.) |
| Item Weight | 1 pound (454 Grams) |
| Product Dimensions (L x W x H) | 3.44 x 3.44 x 4.5 inches |
| Temperature Range | -65°F to 400°F (-54°C to 204°C) |
| Water Resistance Level | Waterproof |
| Suggested Applications | Thread fittings, plumbing applications, water lines, oil lines, fuel lines |
| UPC | 0686226800459 |
8. Warranty and Support
Specific warranty information for the Permatex 80045 Pipe Joint Compound is not provided in the product details. For any product-related inquiries, technical support, or to obtain the most current warranty information, please contact Permatex directly through their official website or customer service channels.
Permatex is a leading manufacturer of chemical products for automotive maintenance and repair. Additional information and support resources may be available on their brand store:
- Permatex Brand Store: Visit the Permatex Store