1. Introduction
This manual provides essential information for the safe and efficient use of your new Whirlpool AKG 958 Cooker Hood. Please read these instructions carefully before installation, operation, or maintenance. Keep this manual for future reference.

Figure 1: Whirlpool AKG 958 Cooker Hood. This image shows the integrated wall chimney hood, highlighting its design and how it fits into a kitchen environment.
2. Safety Information
Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and injury to persons.
- Ensure the power supply voltage matches the rating plate on the appliance.
- Do not allow children to operate the appliance.
- Regularly clean the hood and its filters to prevent grease buildup, which can be a fire hazard.
- Do not flambé under the cooker hood.
- Ensure adequate ventilation in the room when the cooker hood is used simultaneously with appliances burning gas or other fuels.
- Disconnect the appliance from the main power supply before any cleaning or maintenance.
- Installation must be carried out by a qualified technician in accordance with local regulations.
3. Installation and Setup
The Whirlpool AKG 958 is an integrated wall chimney type cooker hood designed for seamless integration into your kitchen cabinetry. Professional installation is recommended.
3.1 Unpacking
- Carefully remove the cooker hood from its packaging.
- Check for any damage during transit. If damage is found, do not install and contact your retailer.
- Ensure all components listed in the packing list are present.
3.2 Mounting
- This appliance is designed as a wall chimney hood and must be securely mounted to a sturdy wall structure above the cooking surface.
- Refer to the detailed mounting template (if provided separately) for precise drilling locations.
- Ensure the minimum distance between the hob and the lower part of the hood is maintained as per local safety regulations (typically 65-75 cm for electric hobs and 75-85 cm for gas hobs).
3.3 Electrical Connection
- The hood operates with an electric cable power source.
- Connect the appliance to a properly grounded electrical outlet.
- The voltage requirement is 1 Volt (as per specifications, though this seems unusually low for a cooker hood, it's taken directly from the source data). Ensure your electrical supply matches this.
- Installation must comply with all local electrical codes.
3.4 Ducting (Extraction Mode)
- If operating in extraction mode, connect the hood's outlet to an external ducting system.
- Use rigid ducting with the largest possible diameter for optimal performance and reduced noise.
- Avoid sharp bends and long duct runs.
3.5 Recirculation Mode (Optional)
If operating in recirculation mode, ensure carbon filters are installed (sold separately, if not included) to purify the air before returning it to the kitchen. No external ducting is required for this mode.
4. Operation
The Whirlpool AKG 958 Cooker Hood features an electronic control system for easy operation.
4.1 Power On/Off
- Press the power button to turn the hood on or off.
4.2 Fan Speed Control
The hood offers 3 fan speeds to suit various cooking needs.
- Speed 1 (Low): Ideal for simmering or light cooking.
- Speed 2 (Medium): Suitable for general cooking.
- Speed 3 (High): Use for frying, grilling, or when producing a lot of steam/smoke.
- Select the desired speed using the respective control buttons.
4.3 Lighting
The hood is equipped with a light feature to illuminate your cooking area.
- Press the light button to turn the light on or off.
5. Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your cooker hood. Always disconnect the power supply before performing any maintenance.
5.1 Cleaning the Exterior
- Clean the exterior surfaces with a soft cloth dampened with warm soapy water.
- Do not use abrasive cleaners, corrosive detergents, or harsh brushes, as these can damage the finish.
- Dry thoroughly after cleaning.
5.2 Cleaning/Replacing Grease Filters
The Whirlpool AKG 958 uses a fleece filter system for grease filtration. These filters should be cleaned regularly or replaced as needed.
- Frequency: Depending on usage, grease filters should be cleaned every 2-4 weeks.
- Removal: Locate the filter release latches and carefully remove the grease filters.
- Cleaning: Wash the fleece filters by hand in warm soapy water or in a dishwasher on a low-temperature cycle. Ensure they are completely dry before reinstallation.
- Replacement: If filters are heavily soiled or damaged, replace them with genuine Whirlpool replacement filters.
5.3 Replacing Carbon Filters (Recirculation Mode Only)
If your hood is operating in recirculation mode, carbon filters are essential for odor removal. These filters are not washable and must be replaced.
- Frequency: Carbon filters typically need replacement every 3-6 months, depending on usage.
- Replacement: Follow the instructions provided with the replacement carbon filters for proper installation.
5.4 Replacing Light Bulbs
- Ensure the hood is disconnected from the power supply and the light bulb has cooled down.
- Carefully remove the old bulb and replace it with a new bulb of the same type and wattage.
6. Troubleshooting
Before contacting customer service, refer to the following table for common issues and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Hood does not operate. | No power supply. | Check if the appliance is plugged in and the circuit breaker is not tripped. |
| Poor suction performance. | Grease filters are clogged. Ducting is obstructed or too long/bent. Incorrect fan speed selected. | Clean or replace grease filters. Check ducting for obstructions or excessive bends. Select a higher fan speed. |
| Excessive noise. | Loose components. Incorrect ducting installation. Fan motor issue. | Check for and tighten any loose parts. Ensure ducting is properly installed and secured. If noise persists, contact service. |
| Light does not work. | Light bulb is faulty. | Replace the light bulb (refer to Section 5.4). |
If the problem persists after attempting these solutions, please contact Whirlpool customer support.
7. Specifications
| Feature | Detail |
|---|---|
| Model | AKG 958 |
| Type | Integrated Wall Chimney Hood |
| Width | 60 cm |
| Dimensions (Product) | 50 x 50 x 28 cm |
| Weight (Item) | 250 g |
| Number of Motors | 1 |
| Number of Speeds | 3 |
| Maximum Air Extraction Rate | 207 m³/h |
| Suction Rate | 207 |
| Filtering System | Fleece Filter |
| Noise Level | 61 Decibel |
| Power Source | Electric Cable |
| Voltage | 1 Volt |
| Special Features | Light |
| Electronic Ignition System Type | Electronic |
| Extended Extraction Area | No |
| GTIN | 08003437626142 |
Note: Specifications are subject to change without notice for product improvement.
8. Warranty and Customer Support
Your Whirlpool AKG 958 Cooker Hood comes with a manufacturer's warranty. Please refer to the warranty card included with your purchase for specific terms and conditions, including warranty period and coverage.
For technical assistance, spare parts, or to schedule a service appointment, please contact Whirlpool Customer Service. Have your model number (AKG 958) and serial number ready when you call.
You can find contact information for Whirlpool Customer Service on their official website or in the documentation provided with your appliance.
Whirlpool Official Website: www.whirlpool.com (Please select your regional website for local support information.)





