1. Important Safety Information
Please read and understand all instructions before beginning installation. Failure to do so may result in electric shock, fire, or other injuries that could be fatal or cause property damage.
- WARNING: Risk of electric shock. Disconnect power at the circuit breaker or fuse box before installation or servicing.
- All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC). Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
- Use only UL/cUL listed wire connectors.
- This product may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm (Proposition 65 warning). Wash hands after handling.
2. Product Overview
The Progress Lighting P5607-31 is a traditional 1-light outdoor wall lantern featuring clear flat glass and a textured black finish. It is designed for outdoor use, providing illumination for porches, patios, and other exterior areas.
Figure 2.1: Front view of the Progress Lighting P5607-31 outdoor wall lantern in textured black with clear glass.
Figure 2.2: Line drawing illustrating the design of the P5607-31 outdoor wall lantern.
3. Setup and Installation
3.1 Package Contents
Verify that all components are present before beginning installation. The package typically includes the fixture, mounting hardware, and an installation sheet.
3.2 Pre-Installation
- Turn off power at the main circuit breaker or fuse box.
- Carefully unpack the fixture and components.
3.3 Mounting the Fixture
This fixture is designed for wall mounting. Ensure the mounting surface is secure and can support the weight of the fixture.
- Attach the mounting bracket to the junction box using the provided screws.
- Ensure the bracket is level and securely fastened.
3.4 Electrical Connections
Connect the fixture wires to the house wires according to the following:
- Connect the black wire from the fixture to the black (hot) wire from the junction box.
- Connect the white wire from the fixture to the white (neutral) wire from the junction box.
- Connect the bare copper or green ground wire from the fixture to the green or bare copper ground wire from the junction box.
- Secure all connections with UL/cUL listed wire connectors.
3.5 Securing the Fixture
- Carefully tuck all wires into the junction box.
- Align the fixture with the mounting bracket and secure it using the provided screws or nuts.
3.6 Bulb Installation
This fixture uses one (1) 100-Watt maximum, medium base (E26) bulb. An A19 shape bulb is recommended for optimal appearance with the clear glass.
Figure 3.1: Bulb information indicating an E26 (Medium Base) bulb and recommending an A19 bulb shape for this fixture.
- Screw the bulb into the socket until snug. Do not overtighten.
- This fixture is dimmable when used with compatible wall dimmers and dimmable light bulbs.
3.7 Recommended Placement
For aesthetic balance, wall lanterns are often sized to be approximately 1/4 the height of the door they flank.
Figure 3.2: Example of wall lantern height recommendation: 1/4 of the door height. For a 96-inch door, a 24-inch fixture is suggested.
Figure 3.3: Illustration of outdoor wall lantern placement on a house, demonstrating appropriate sizing and spacing for garage and entryways.
4. Operation
Once installed and power is restored, the fixture operates by a standard wall switch. If a compatible dimmer switch and dimmable bulb are used, the light output can be adjusted.
5. Maintenance
5.1 Cleaning
To clean the fixture, turn off the power and wipe with a soft, damp cloth. Do not use abrasive cleaners or solvents as they may damage the finish or glass.
5.2 Bulb Replacement
Before replacing the bulb, ensure the power is turned off at the circuit breaker. Allow the bulb to cool completely before touching. Replace with a new 100-Watt maximum, E26 base bulb.
6. Troubleshooting
- Light does not turn on:
- Check that the power is turned on at the circuit breaker.
- Ensure the bulb is securely screwed into the socket and is not burnt out.
- Verify all electrical connections are secure.
- Inspect for any defective electrical components or wiring.
- Fuse blows or circuit breaker trips:
- Check for crossed wires or short circuits.
- Ensure the bulb wattage does not exceed the fixture's maximum rating (100W).
7. Specifications
Figure 7.1: Detailed dimensions of the P5607-31 fixture, showing a width of 4-9/16 inches and a height of 8-5/8 inches.
| Feature | Detail |
|---|---|
| Model Number | P5607-31 |
| Brand | Progress Lighting |
| Dimensions (L x W x H) | 4.5" x 4.5" x 8" (4-9/16" W x 8-5/8" H) |
| Item Weight | 1 pound (16 ounces) |
| Material | Aluminum |
| Finish Type | Clear (Glass) |
| Color | Black |
| Style | Traditional |
| Light Source Type | Incandescent (compatible with LED) |
| Bulb Base | E26 (Medium Base) |
| Max Wattage | 100 Watts |
| Voltage | 120 Volts |
| Brightness | 1600 lumen (with 100W incandescent) |
| Water Resistance Level | Water Resistant |
| Mounting Type | Protruding (Wall Mount) |
| UPC | 785247560738 |
8. Warranty Information
This Progress Lighting product is covered by a 1-year Limited Warranty. This warranty guarantees your satisfaction with the purchase and includes professional after-sales customer service support. For specific details regarding warranty claims or service, please refer to the original purchase documentation or contact Progress Lighting customer service.
9. Support
For further assistance, technical support, or to inquire about replacement parts, please contact Progress Lighting customer service. Contact information can typically be found on the manufacturer's official website or on the product packaging.
